background image

Warranty & Specifications 

IMPORTANT NOTICE

We, the manufacturer, reserve the right to change the product and/

or specifications in this manual without notification. The manual is for 

information usage only and the pictures and drawings depicted herein are 

for reference only.

Warranty Repair and Service

Do not return this product to the store for warranty issues or repair. Call 

our customer service department at 

720-287-5182,  1-877-487-8275, 

 or 

visit

 

www.dirtyhandtools.com

 for the location of the nearest service center.

Record the information below for future reference.

Model No.
Serial No.
Date of Purchase
Place of Purchase

 

SKU/Part No. 

106717 

106922

 Description 

46” Rough Cut Brush Mower 

46” Rough Cut Brush Mower

 Engine 

19 HP/597cc Kohler SV591 Engine* 

20 HP/608cc Loncin Engine*

  

EPA/CARB Approved 

EPA/CARB Approved

 Engine Fuel Capacity** 

2.5 gallons 

2.5 gallons

 Remote Control 

Key, throttle, blade control with 5 ft cord 

Key, throttle, blade control with 5 ft cord

 Cutting Width 

46 inches 

46 inches

 Cutting Height 

4”, 5”, 6.25” and 7.5” adjustable 

4”, 5”, 6.25” and 7.5” adjustable

 Cutting Capacity 

4 - 8 foot high grass, weeds and brush,  up to 2 inch diameter saplings

 Tires 

18 x 6.50-8, all terrain 

18 x 6.50-8, all terrain

 Blades 

Breakaway design, 1.25” x 11”L, pair 

Breakaway design, 1.25” x 11”L, pair

 Belt 

Type B52 

Type B52

 Dimensions 

64”W x 110”L (fully extended) x 28.5”H 

64”W x 110”L (fully extended) x 28.5”H

 Shipping Weight 

635 Lbs. 

635 Lbs.

 Warranty 

2 Year / 2 Year Limited Warranty 

2 Year / 2 Year Limited Warranty

*As rated by engine manufacturer

** Not included, shipped without engine oil

Specifications

1100 W 120th Ave., Suite 600

Westminster, CO 80234 • 720-287-5182

Dirty Hand Tools® is a brand of

For Service or Questions

Call 1-877-487-8275

720-287-5182

www.dirtyhandtools.com

Summary of Contents for 106717

























Reviews: