background image

10

Operation

WARNING:  Read and thoroughly understand all instructions 

and safety information before assembling or operating this post 

hole digger. Failure to do so may cause serious injury or death. 

1.  In a separate container mix gasoline and 2-cycle engine oil 

in a ration of 25 parts gasoline to one part 2-cycle engine oil 

(approximately 1 gallon of gas to 2.5 fluid ounces oil). Mix 

thoroughly before adding to the post hole digger’s fuel tank.

2.  Turn the engine switch on the right handle bar to the ON 

position (backwards).

3. Slide the choke level to the choke position.

4. Press the fuel priming bulb three or four times.

5. Pull the recoil handle slowly and release.

6. Pull the recoil handle quickly to start engine.

7. Allow the engine to run for a few minutes 

    then move choke to the run position.

8.  Lower the auger to the ground at the desired angle for hole 

digging.

9.  Engage the power trigger to start digging at a slow speed 

lowering the auger slowly as the hole is dug. Increase the 

speed as the auger goes deeper into the ground by depressing 

the power trigger further. The type of soil will determine the 

proper auger speed. A very hard or compacted soil may require 

operation at varying speeds to be the most efficient in digging. 

10.  After the desired hole depth has been reached, spin the auger 

at a high speed to clear the hole of soil. Reduce the speed 

before withdrawing the auger from the hole by easing up on 

the power trigger, then releasing the power trigger entirely.

STOP THE AUGER BY PUSHING THE

ENGINE ON/OFF SWITCH FORWARDS

If a rock or other obstacle is encountered that is too large for the 

auger to displace the post hole digger will begin to vibrate. Slowly 

withdraw the auger from the hole completely.  Push the engine 

on/off switch forward to stop the engine and remove the obstacle 

manually. Slowly lower the auger into the hole and engage the 

power to complete digging the hole.

!

WARNING

!

CAUTION

FUEL MIX:

25:1

MIX

THOROUGH

LY

2.5 FL. OZ.

2-CYCLE

OIL

1

GALLON

GAS

MIX

GAS

OIL

10

48

99

FUEL MIX:

25:1

MIX

THOROUGH

LY

2.5 FL. OZ.

2-CYCLE

OIL

1

GALLON

GAS

MIX

GAS

OIL

10

48

99

2 CYCLE

CAUTION !

FIRE DANGER

FUEL WITH

COOL ENGINE !

104898

CHOKE

LEVER

Summary of Contents for 104306













Reviews: