background image

13

Operating Precautions

READ, UNDERSTAND AND FOLLOW ALL OF THE 

PRECAUTIONS BELOW.

Always perform the pre-start checklist before starting the engine.

•  Never operate the tiller without safety shields in place.

•  Keep hands, feet, and clothing away from rotating parts. Keep clear 

of tiller tines at all times.

•  Tines rotate when the engine is running and drive lever is depressed 

(pulled towards the handlebars). 

Releasing the drive lever stops the tines.

•  Use extreme caution when operating on or crossing gravel drives, 

walks, or roads. Stay alert for hidden hazards or traffic.

•  After striking an obstacle, stop the engine, remove the wire from the 

spark plug, inspect the tiller for damage and repair before restarting.

•  If tines become clogged, stop the engine and disconnect the spark 

plug wire

 before removing any obstruction.

•  Engine muffler will be hot from operation. Do not touch it with bare 

skin or a severe burn may result.

•  If the unit vibrates abnormally, stop the engine and check immediately 

for the cause. 

Vibration is an indication of a potential problem.

• Do not run the engine indoors; exhaust fumes are deadly.

•  Do not overload the tiller by trying to till too deep or too fast.

•  Never operate the machine at high transport speeds on slippery 

surfaces. Look behind and use care when backing.

•  Use only attachments and accessories approved by the manufacturer.

• Never operate the tiller without good visibility or adequate light.

•  Be careful when tilling in hard ground. The tines may catch in the 

ground and propel the tiller backwards. 

If this occurs, let go of the 

handlebars and do not restrain the machine.

•  Take precautions when leaving the machine unattended. Disengage 

all control levers, stop the engine, wait for all moving parts to stop, and 

make certain guards and shields are in place.

•  Shut off the engine when leaving the operating position for any 

reason. Wait for all moving parts to stop.

OPERATION OF ANY TILLER CAN RESULT IN FOREIGN 

OBJECTS BEING THROWN.  ALWAYS WEAR

SAFETY GLASSES DURING OPERATION.

!

CAUTION

!

WARNING

Summary of Contents for 101571





















Reviews: