19
GB
5 Maintenance
5.3 Cleaning the exhaust filter
Check the exhaust filter every time you clean the motor protection filter
Z
chapter 5.2, „Cleaning dust bin and motor protection filter“
and clean it if
it is dirty.
1.
Switch off the appliance,
Z
chapter 4.3, „Switching off“
.
2.
Push the release catch of the exhaust filter cover down (Fig. 12/A) and
open the exhaust filter cover.
3.
Remove the exhaust filter (Fig. 12/B).
4.
Hold the dust bin over a dustbin.
5.
Remove any residual dust by tapping. If the exhaust filter is still dirty,
thoroughly rinse it by hand until all dirt is removed.
6.
If the exhaust filter is damaged, replace it (
Z
chapter 5.4, „Spare parts
and accessories“
).
7.
Put the exhaust filter holder with the freshly fitted filter back into its
bracket (Fig. 13/A).
8.
Attach the exhaust filter cover at the bottom side first (Fig. 13/B) before
folding it up firmly. It will audibly snap into place.
5.4 Spare parts and accessories
Accessory parts and spare parts can be reordered:
Contact
Z
Page 62, „International Service“
The following accessories and spare parts can be reordered:
5.5 Before you send in the appliance
Before contacting or even sending the appliance to us, use the following ta-
ble to check whether you can correct the problem yourself.
B
A
12
B
A
13
ATTENTION:
The filter is washable, but it may not be cleaned in dishwashers or wash-
ing machines. Also, do not use detergents or brushes with hard bristles
to clean them. Let the filter dry for approx. 24 hours at room temperature
after washing it. Only put it back in place when it is completely dry.
ATTENTION:
Only use original spare parts from the scope of delivery or those which
you have purchased by reordering.
Item number
Content
2815001
Motor protection filter set consisting of: 1 foam plastic
filter element (round) + 1 filter holder = 1 dual motor
protection filter; 1 small motor protection filter
2815002
1 exhaust filter
M203
1 parquet brush
M209
1 turbo brush
M219
1 mini turbo brush
WARNING:
Risk of injury! Never use a faulty appliance! Always switch off the appli-
ance and disconnect it from the mains before starting troubleshooting
Z
chapter 4.3, „Switching off“
.
Problem
Solution
Cleaning indi-
cator (Fig. 1/
6) lights up or
cleaning re-
sults are not
satisfactory.
The dust bin is full.
Empty the dust bin,
Z
chapter 5.1, „Emptying the dust bin
module“
.
The filters are dirty.
Clean the respective filter
Z
chapter 5.2, „Cleaning dust
bin and motor protection filter“
or
Z
chapter 5.3, „Clean-
ing the exhaust filter“
.
Nozzle, telescopic tube or suction hose is blocked.
Remove the obstruction. If necessary, use a long wood-
en stick (e.g. a broomstick) to do this.
The vacuum
cleaner stops
suddenly.
Overheating protection has tripped (possibly because
you ignored the lit cleaning indicator for too long).
Switch the appliance off and pull the plug out of the sock-
et. Eliminate the cause of overheating (e.g.
Z
chapter
5.2, „Cleaning dust bin and motor protection filter“
). Wait
for about 45 minutes. After the appliance has cooled off,
you may switch it on again.
The cleaning
results are un-
satisfactory in
spite of the
appliance
working cor-
rectly (clean-
ing indicator
(Fig. 1/6)
does not light
up).
The bypass vent (Fig. 1/20) is open.
Close the bypass vent (Fig. 1/20).
The attached nozzle is unsuitable.
Change the nozzle,
Z
chapter 3.2, „Selecting the proper
nozzle“
.
The position of the “carpet/hard floor” selector (Fig. 1/27)
is inappropriate.
Set the “carpet/hard floor” selector (Fig. 1/27) to the cor-
rect position for the type of floor,
Z
chapter 4.2, „How to
vacuum“
, step 4.
NOTE:
If you were unable to solve the problem using the information in the table
above, please contact our Customer Service (contact
Z
Page 62,
„International Service“
).
Problem
Solution
M2815.book Seite 19 Dienstag, 14. Juli 2015 4:07 16
