Directed 403.VW10 Installation Manual Download Page 11

11

403.VW10 2.00 2008 Volkswagen GTI
©2022 VOXX•DEI LLC.  All rights reserved.

Module

Connects To

Conn./Pin

Color

Description

Wire Location

(+/-)

Wire Color

H3/1

Green

(-) W2W Only - Lock Input

Remote Starter

H3/2

Blue

(-) W2W Only - Unlock Input

Remote Starter

H3/3

Red/White

(-) W2W Only - Trunk Input

Remote Starter

H3/4

White/Violet

No Connection

No Connection

H3/5

Violet/Black

No Connection

No Connection

H3/6

White/Black

No Connection

No Connection

H3/7

Pink/White

(+) Pk Light Input

Remote Starter

H3/8

Violet

(+) W2W Only - Starter Input

Remote Starter

H3/9

Pink

(+) W2W Only - Ignition Input

Remote Starter

H3/10

Blue/White

(-) W2W Only - Ground When Running (Status) Input

Remote Starter

D2D 4-pin white connector (H4)

Module

Conn./Pin

Color

Description

H4/1

Green

H4/2

Black

H4/3

Blue

H4/4

Red

RF 2-pin white connector (H5)

Module

Conn./Pin

Color

Description

H5/1

N/A

No Connection

H5/2

N/A

No Connection

Additional remote start connections

(Not all of these connections may be required for your installation. Refer to the wiring diagram for vehicle-specific connections.)

Wire

Connects To

Wire Location

(+/-)

Wire Color

12 Volts

VESCM-Relay Box under driver dash, black 2 pin plug (L), pin 1

+

Red/Black (40A)

Brake Wire

VESCM-Relay Box under driver dash, black 16 pin plug (E), pin 2

+

Black/Red (test with ignition on)

Ignition

Steering Column Module, black 20 pin plug, pin 17

+

Black

Starter

Steering Column Module, black 20 pin plug, pin 18

+

Red/Black or Red/Brown

Summary of Contents for 403.VW10






















Reviews: