Directed 403.SUBARU2 Installation Manual Download Page 5 | Manualshive

Page: 5 / 21

Directed 403.SUBARU2 Installation Manual Download Page 5

5

403.SUBARU2 1.38 2010 Subaru Outback
©2022 VOXX•DEI LLC. All rights reserved.

Pre-installation and application warnings

START

HERE

This section highlights important information for this specific firmware and will assist in pricing accordingly, as
well as bringing awareness to any operational or vehicle limitations.

Compatibilities and Requirements

T-Harness
compatible

T-Harness is not compatible.

Keys required for
programming

1

Keys required
for operation

0

Vehicle Takeover

Refer to the

Quick Reference Guide

section for more details.

Firmware notes

Key2GO:

Mandatory to control the immobilizer override in this firmware.

All connectors are displayed from the wire side (unless specified otherwise).

Refer to the "Vehicle connections" following the installation diagram.

Footnotes

[1]

Hood pin:

The installation of an aftermarket hood pin is only required on vehicles that are not equipped with a factory

hood pin, or if not supported in data.

[2]

Tach:

Optional connection required on some remote starters, which do not support a tach signal in D2D.

[3]

Keysense connection:

Only needed if keysense is not recognized through data at the time of programming. Refer to the

"LED diagnostics & Troubleshooting" section for more details.

[4]

Key Release Output:

Only required for Pit Stop mode or manual transmission vehicles.

«
...
3
4
5
6
7
...
»

Summary of Contents for 403.SUBARU2






















Reviews:

No comments