manualshive.com logo in svg

Directed 403.SUBARU2, Installation Manual, Page: 12 / 21

Share
Download
Directed 403.SUBARU2 Installation Manual Download Page 12

12

403.SUBARU2 1.38 2010 Subaru Outback
©2022 VOXX•DEI LLC.  All rights reserved.

Module programming for convenience features only (skip transponder)

 Refer to "LED diagnostics and troubleshooting" for more information and for troubleshooting purposes.

1

Ensure vehicle is in a safe location and cannot move forward during programming. For vehicles 
equipped with a manual transmission, make sure the gearshift is in the neutral position.

2

The harnesses must be connected in this exact order:
 

1. Connect the 14-pin.

 

2. Connect the 12-pin.

 

3. Connect the 10-pin.

When the LED turns on solid red, proceed with the next step.

Solid

Connect

14

12

10

4

2

3

Press the programming button five (5) times.
The LED turns ON solid orange.

 

Solid

Press &

Release x5

4

Turn the ignition ON and wait until the LED turns OFF.

START

Key IN

ON

OFF

Off

5

Turn ignition OFF and remove the key from the ignition barrel.

START

Key OUT

ON

OFF

You have successfully completed the module programming sequence.

Summary of Contents for 403.SUBARU2






















Reviews:

No comments