background image

29

© 2009 Directed Electronics. All rights reserved.

Glossary of terms

Control Center:

 The Control Center contains the system’s radio-frequency 

antenna, the Control button, and the Status LED. For maximum remote-control 

range, the Control Center is usually located at the top of the windshield, 

centered near the rear-view mirror.

Control Module:

 The “brain” of your system. Usually hidden underneath the 

dash area of the vehicle. It houses the microprocessor which monitors your 

vehicle and controls all of the system's functions.

Failsafe® Starter Kill 

(if equipped): An automatic switch controlled by the 

system which prevents the vehicle’s starter from cranking whenever the system 

is locked. The vehicle is never prevented from cranking when the system is 

unlocked in Valet® Mode, or should the Starter Kill switch fail. Your system 

is ready for this feature, however installation of this feature may require ad-

ditional labor.

Input:

 Any physical connection to the system. An input can be provided by 

existing systems in the vehicle, such as ignition or courtesy lights.

In-vehicle status LED:

 A light used to indicate the status of your system. It is 

located on your systems Control Center.

MTS:

 Manual transmission start. Procedure required for using the remote start 

in a vehicle with a manual transmission.

RF:

 Radio frequency

Control Button: 

A small push button switch located on your systems Control 

Center. It is used to override the starter interrupt when a remote is lost or dam-

aged, or to enter or exit Valet Mode.

Summary of Contents for VIPER 5101













































Reviews: