background image

13

© 2011 Directed Electronics. All rights reserved.

4.  Siren Duration

1.  30sec: the siren output for full trigger activations and Panic mode is 30 seconds

2.  60sec: the siren output for full trigger activations and Panic mode is 60 seconds

5.  Ign-controlled Locks

1.  No Ign-locking: the door lock/unlock outputs will not activate when ignition is turned on/off

2.  Lock & Unlock: the door lock & unlock output will activate when ignition is turned on & off

3.  Lock Only: the door lock output will activate when ignition is turned on

4.  Unlock Only: the door unlock output will activate when ignition is turned off

6.  Door Lock Pulses

1.  Single: the door lock & unlock outputs will pulse once 

2.  Double Unlock only: the unlock output only will pulse twice 

3.  Double Lock Only: the lock output only will pulse twice 

4.  Double Lock & Unlock: the lock & unlock outputs will pulse twice

7.  Door Lock Output Duration

1.  0.8 sec.: the door lock output pulses will be 800 ms in duration

2.  3.5 sec.: the door lock pulses will be 3.5 seconds in duration

3.  0.4 sec.: the door lock pulses will be 400 ms in duration

 

8.  Ignition Controlled 2nd Unlock

1.  After first unlock: for Ign-controlled unlocking, the 2nd unlock will activate 800 ms after the first (driver 

door) unlock

2.  With first unlock: for Ign-controlled unlocking, the 2nd unlock will activate at the same time as the first 

(driver door) unlock

9.  Comfort Closure

1.  No comfort Closure: Comfort Closure is defeated when arming 

2.  Comfort Closure 1: the door lock pulse (or 2nd pulse for double pulses) will remain on for 20 sec-

onds.

3.  Comfort Closure 2: 800mS following the end of the door lock pulse (or 2nd pulse for double pulses); 

the door lock output will turn on again for 20 seconds.

10. Horn Function

1.  Full Alarm Only: the horn output will pulse only during full trigger events.

2.  Siren Function 20/30/40/50ms: The horn output will emulate the siren output with selectable chirp 

output timing to compensate for OEM horn inefficiency. 

11. Hood Switch Type

1.  Normally Open: for vehicles with a hood switch that rests at ground when the hood is OPEN

2.  Normally Closed: for vehicles with a hood switch that rests at ground when the hood is CLOSED

12. Sensor Full Trigger

1.  Single: full trigger activation of only one sensor is required to fully trigger the alarm

2.  Double: full trigger activation of two sensors within a ten second period is required to fully trigger 

the alarm.

13. Door Switch Type

1.  Normally Open: for vehicles with door switches that rest at ground when the door is OPEN

2.  Normally Closed: for vehicles with door switches that rest at ground when the door is CLOSED

14. Trunk Switch Type

1.  Normally Open: for vehicles with a trunk switch that rests at ground when the trunk is OPEN

2.  Normally Closed: for vehicles with a trunk switch that rests at ground when the trunk is CLOSED

15. Remote Button Unlock (Ign off)

1.  On: a message telling the remote control to unlock the keypad is sent each time the vehicle ignition 

is turned off

2.  Off: no message is sent

Summary of Contents for Clifford 510.4X
























Reviews: