Directed Electronics 560XV Installation Manual Download | Manualshive

Page: 17 / 55

background image

© 2003 Directed Electronics, Inc. Vista, CA

17

primary harness (H1) wire connection guide

This wire supplies a (-)500 mA ground as long as the system is armed. This output ceases as soon as the system

is disarmed. The orange wire may be wired to an optional Directed Electronics 8618 starter kill relay.

As shipped, this wire should be connected to the (+) parking light wire. If the light flash polarity jumper under

the sliding door is moved to the opposite position (see

Internal Programming Jumper

section of this guide), this

wire supplies a (-) 200 mA output. This is suitable for driving (-) light control wires in Toyota, Lexus, BMW, some

Mitsubishi, some Mazda, and other model cars.

(+) Positive Light Flash Output

(-) Light Flash Output

NOTE:

For parking light circuits that draw 10 amps or more, the internal jumper must be switched

to a (-) light flash output. (See the Internal Programming Jumper section of this guide.)

P/N 8617

or a standard automotive SPDT relay must be used on the H1/2 light flash output harness wire.

H1/2 WHITE (+/-) selectable light flash output

H1/1 ORANGE (-) ground-when-armed output

«
...
15
16
17
18
19
...
»

Summary of Contents for 560XV
























































Reviews:

No comments

Related manuals for 560XV

Brand: VTEC Pages: 14

Excalibur AL-700LC

Brand: Omega Pages: 10

Smoky Mountain Great Outdoors 3625BGD

Brand: Landmann Pages: 29

Brand: ELRO Pages: 2

Brand: ZAZU Pages: 8

Brand: Uniden Pages: 8

Brand: La Crosse Technology Pages: 8

ALCDVR32-SL V1.0

Brand: COP-USA Pages: 12

Brand: Trevi Pages: 8

Intelliguard 750

Brand: Directed Electronics Pages: 45

Brand: Directed Electronics Pages: 55

Brand: Cofem Pages: 2

Brand: Code Alarm Pages: 8

Brand: CrimeStopper Pages: 12

Brand: Vitek Pages: 2

Brand: Discovery Kids Pages: 8

VIP RS3200 plus

Brand: Toyota Pages: 16

Brand: Telefunken Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands