manualshive.com logo in svg

Directed Electronics 560XV, Installation Manual, Page: 48 / 55

Share
Download
Directed Electronics 560XV Installation Manual Download Page 48

48

© 2003 Directed Electronics, Inc. Vista, CA

timer mode

By pressing the remote 

and 

buttons the parking lights will flash 4 times and then start the vehicle

and run for the set duration. The remote start can be shut off by the transmitter by pressing the remote start

button 

and remain in timer mode, but if any other shut down zones or the ignition becomes active the

timer mode will cancel.

1. Press Timer mode buttons.

2. The vehicle will confirm with 4 parking light flashes.

3. A 1-second delay will start.

4. The system will start the car and will run for the specified duration, unless shut down by the remote start

button 

. If shut down with the remote start button 

the system will remain in timer mode.

5. The system will start every 3 hours until canceled by the brake, hood, or neutral safety shut-down wires.
To exit timer mode, turn the ignition switch on any time the engine is not running. The parking lights will flash
4 times, indicating timer mode has been exited.

5. The system will start every 3 hours until canceled by the brake, hood, or neutral safety shut-down wires.

table of zones

When using the Diagnostic functions, use the Table of Zones to see which input has triggered the system. It is

also helpful in deciding which input to use when connecting optional sensors and switches.

NOTE

: The Warn Away® response does not report on the LED.

ZONE NO.

TRIGGER TYPE

INPUT DESCRIPTION

1

Multiplexed Input

BLUE (H1/6)

2

Multiplexed Shock Sensor Input Mux BLUE wire.

3

Door Trigger

GREEN (H1/5) and VIOLET (H1/7).

4

Multiplexed Shock Sensor

Mux GREEN wire

5

Ignition

Yellow ribbon harness wire

6

Hood Brake Trigger

GRAY on the 6-pin shutdown harness.

Summary of Contents for 560XV
























































Reviews:

No comments