background image

19

©

2001 Directed Electronics, Inc.

Glossary of Terms  

Back-Up Battery Siren:

Noise generating device responsible for

generating the "chirps" you hear, as well as the sound you hear

when the alarm is triggered.

Control Unit:

The "brain" of your system. It houses the micro-

processor which monitors and controls all of the system's functions.

Failsafe

®

Starter Kill:

An automatic switch controlled by the secu-

rity system which prevents the starter from cranking whenever the

system is armed. The starter is never prevented from cranking

when the system is disarmed, in Valet

®

mode, or should the starter

kill switch itself fail.

Input:

A physical connection to the system. An input can be pro-

vided by a sensor, pinswitch or to existing systems on the vehicle,

such as the ignition.

LED:

Red light mounted somewhere in the vehicle. It is used to

indicate the status of your system. It is also used to report trig-

gers and faults in the system or sensors.

Shock Sensor:

This system is packaged with a Doubleguard

®

Shock

Sensor. This sensor is on-board the control module and is designed

to detect impacts to the vehicle.

Transmitter: 

Hand-held, remote control which operates the 

various functions of your system.

Summary of Contents for 200


























Reviews: