background image

5

© 2003 Directed Electronics, Inc 

High-powered car audio
systems may produce sound

pressure levels that exceed the
threshold at which hearing loss may
result. 

They may also impair a driver’s ability to
hear traffic sounds or emergency vehi-
cles. Use common sense and practice
safe listening habits when listening to or
adjusting your audio system.

WARNING

FEATURES

„

Dual high-speed MOSFET switching
power supplies.

„

Complimentary bipolar outputs (ch
1-4), and high-current MOSFET
outputs (sub channel).

„

Five channel expandable architec-
ture supports single or multiple amp
system designs.

„

Thermal, DC offset, reverse polarity,
and short circuit protection with
status LED.

„

Top-mounted controls are easily
accessed for system tuning.

„

Dual continuously variable 12
dB/octave two-way active
crossovers (ch 1-4).

„

Continuously variable 24 dB/
octave low-pass crossover (sub
channel).

„

Switchable 30Hz, 24 dB/octave
subsonic filter and phase invert
switch (sub channel).

„

Remote subwoofer level control and
switchable 8 dB bass EQ function.

„

Two, four, and six channel input
allows full access to source or
processor output functions.

„

Master/slave function allows
synced bridged or parallel operation
with model 750d.

„

Summed stereo full-range RCA
output jacks.

„

Gold-plated wire terminals and RCA
connectors ensure maximum signal
transfer.

„

Rugged one-piece extruded heat
sink finished with injection-molded
mounting feet.

Summary of Contents for 1200/5





















Reviews: