background image

13

© 2003 Directed Electronics, Inc 

The Directed 1200/5 channel five
subwoofer section can be combined with
a 750d in a master/slave combination
for increased power and accurate level
matching. They are the Parallel Synced
Gain and External Synced Bridged combi-
nations. 

NOTE:

The Directed 1200/5 is always the master amplifier
in these combinations.

Parallel Synced Gain

The Parallel Synced Gain combination
includes a master amplifier and a slave
amplifier.

In this master/slave combination the
master amplifier’s pre-amp controls
remain active and the slave amplifier’s
pre-amp is bypassed. This allows the
master amplifier to control gain, filter,
and sub-level on both amplifiers.

The Parallel Synced Gain combination
allows the amplifiers to drive their own
separate subwoofer(s) while being
synced together via an in-phase audio
pre-amp signal from the master amplifier.

Woofer wiring connections to the ampli-
fier subwoofer outputs in this combina-
tion should be standard in-phase configu-
rations, creating a parallel speaker
combination. (Refer to 

Parallel Synced

Gain section of this guide for amplifier
and speaker connection diagrams.)

External Synced Bridged

The External Synced Bridged combination
includes a master amplifier and a slave
amplifier.

In this master/slave combination the
master amplifier’s pre-amp controls
remain active and the slave amplifier’s
pre-amp is bypassed. This allows the
master amplifier to control gain, filter,
and sub-level on both amplifiers.

This combination allows the amplifiers to
drive common subwoofer loads while
being synced together via an out-of-
phase audio pre-amp signal from the
master amplifier. In this wiring configura-
tion the master amplifier sends the posi-
tive signal to the speaker while the slave
amplifier sends the negative signal,
making an externally bridged speaker
combination. (Refer to 

External Synced

Bridged section  of this guide for ampli-
fier and speaker connection diagrams.)

Combined Amplifiers Gain
and Filter Settings

Set the Subsonic, EQ, and other filter
settings on the master amplifier to the
positions that achieve the best sound
quality. Follow the adjustment guidelines
discussed in the 

Crossover and Gain

Adjustment section of this guide.

COMBINED AMPLIFIERS

Summary of Contents for 1200/5





















Reviews: