manualshive.com logo in svg

Dionex UltiMate 3000 LCi, Quick Installation Manual

Share
Download
Dionex UltiMate 3000 LCi Quick Installation Manual Download Page 29

UltiMate

®

 3000 Viper™ Capillary Kits for Intelligent LC (LCi) System Solutions 

Quick Installation Guides

 

 

 

January 2010 

Rev. 02 

Page 25

 

 

© 

2010 Dionex 

 

 

5. Viper

™

 Parallel LC Capillary Kits, Dual-Ternary 

Standard (P/N 6040.2810) or Rapid Separation 
(P/N 6040.2809) 

 

5.1  Benefits of Parallel LC 

Parallel LC is an LCi solution for increasing  the throughput for both isocratic and gradient 
separations by efficient use of hardware. The Parallel LC system uses two pumps and two 
detectors, and shares one autosampler and one column compartment. This allows the user to 
operate one Parallel LC setup as two independent HPLC systems,  and therefore increases 
productivity. Chromeleon treats this  configuration as two completely  independent systems 
and manages seamless autosampler and column compartment sharing.  A specialty of the 
Parallel LC configuration is the recommended dual-stack setup (

 5.3). 

The HPLC system with a parallel setup includes a dual-gradient pump with the ability to 
perform two ternary gradients  at the same time, a thermostatted column compartment with 

one 2-position 6-port switching valve 

for column switching, a split loop well-plate 

autosampler,  and  two stackable Dionex  detectors, all of which are fully controlled by the 
Chromeleon Chromatography Data System.  Prior to installation, please consider 

chapter  1

 

for important additional information. 
 

5.2  Scope of Delivery 

Table 9: 

Scope of delivery for the Viper capillary kit, 

RS

 system, Parallel LC, SST (P/N 6040.2809), 

and Viper capillary kit, 

SD

 system, Parallel LC, SST (P/N 6040.2810)

 

Description  

Quantity 

Viper capillary (SST), ID x L 0.13 mm/0.005” x 250 mm or 0.18 mm/0.007” x 250 mm 

4 pcs. 

Viper capillary (SST), ID x L 0.13 mm/0.005” x 350 mm or 0.18 mm/0.007” x 350 mm 

2 pcs. 

Viper capillary (SST), ID x L 0.18 mm/0.007” x 350 mm 

1 pc. 

Viper capillary (SST), ID x L 0.18 mm/0.007” x 550 mm 

1 pc. 

Viper union for direct connection of two Viper capillaries 

2 pcs. 

Capillary marker 

5 pcs. 

Labels for capillary marker 

8 pcs. 

Eluent pre-heater with Viper fitting, ID 0.13 mm ID, volume 2 µL (Included in RS kit only) 

1 pc. 

Laminated flow scheme for Parallel LC 

1 pc. 

Quick installation guide UltiMate 3000 Viper Capillary Kits for Intelligent LC (LCi) 
System Solutions 

1 pc. 

 

Summary of Contents for UltiMate 3000 LCi











































Reviews:

No comments

Brands by name

Popular brands

Load more brands