DimSport YOUTUNE Installation And Use Manual Download Page 9

 

 

 

 

Issued by: PM                approved by DG                    Rev.01                    date 03/09/18                   pag. 9/10 

 

The software's manual mentioned above 
can be downloaded in the reserved area 
of the website 

www.rapidbike.com

  

 
 
 
 
 
 
 
Click AREA RISERVATA 
on bottom right side 
 
 
  
Fill in the form with a valid email address 
and the serial number of Rapid Bike module. 
This number can be found on the card placed 
on module’s rear side 
 
 
 
 
 
 
 
 
or on the label of the connector. 

  

 

 

 

 

 

 

 

 

             

Device doesn’t save automatically the new settings; be sure to press button 

MODE

 for 5 seconds to 

save permanently. 

General information 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

 
 

 
 
 
 
 

 
 

 
 
 

For each feature adjustable with Youtune, Rapid Bike Master software shows the software's settings, 
the actual value of Youtune controller and the resulting value from the sum of the two.  

YOUTUNE controller works with RapidBike Evo and Racing modules without any limitations, and can be 
installed indefinitely on modules having different serial numbers.   

Check on the website 

http://www.dimsport.it/ita/tuning-line/rapidbike

 what features are adjustable 

on your bike using Youtune controller. 
 

For further information regarding Rapid Bike modules' features mentioned in this manual, please refer 
to the Rapid Bike Master software's manual.  

Summary of Contents for YOUTUNE











Reviews: