Three features to Hot Key Navigation:
Select the chose PC
Command mode
Auto scan mode
Select the chose PC:
Press [Ctrl] key twice either on the left or the right side.
Hot Key
Action
[L Ctrl] + [L Ctrl] or
[R Ctrl] + [R Ctrl]
Access between two PCs.
Command Mode:
Press the [Num Lock] key twice, the [Num Lock],
[Caps Lock] and [Scroll Lock] 3 keys will light up and
flashing to access the Command Mode.
a). Directly press the function key [F1] ~ [F2] for
selecting the wanted PC.
b). Press the [Left Ctrl] key to disable [Ctrl] hotkey
function.
c). Press the [Right Ctrl] key to enable [Ctrl] hotkey
function.
d). Press [Esc] key to quit the mode.
Note:
[Ctrl] Hot Key
function
– Selecting PC port.
Auto Scan Mode:
Press [Scroll Lock] key twice to activate the Auto Scan
Mode.
Lights reveal the scan internal from 5 to 30 seconds in
order serially auto scan.
Press [Esc] key to quit the mode.
Note:
Light(s) corresponding timetable
Seconds
Num Lock Caps Lock Scroll Lock
5
seconds
Off
Off
On
10 seconds
On
Off
Off
15 seconds
On
Off
On
20 seconds
Off
On
Off
25
seconds
Off
On
On
30 seconds
On
On
Off
Use the right side number key [+] to increase time.
Use the right side number key [-] to decrease time.
3. The boot-up default of KVM Switch will link to your
first activated PC.
4. Under function of “Auto skip over the power off PC”
and yet LEDs green light turn off, it is incapable of
turning on the PCs by keyboard.
-3-
Troubleshooting
Making sure the cables are qualified and positioned.
Q1 :
The keyboard has no response.
A1a: Re-install the keyboard. Unplug the keyboard
from the Console Port and plug it back again.
A1b: Re-install the KVM Switch. Shut down the PCs,
unplug the cables from the PCs, waiting for five
seconds, plug the cables back and activate the
PCs.
A1c: If under Auto Scan Mode please press [Esc]
key to escape.
A1d: Try another keyboard.
Q2 :
The mouse has no response.
A2a: Re-install the mouse. Unplug the mouse from
the Console Port and plug it back again.
A2b: Re-install the KVM Switch. Shut down the PCs,
unplug the cables from the PCs, waiting for five
seconds, plug the cables back and activate the
PCs.
A2c: Making sure the mouse is set on PS/2 mode.
A2d: Try another mouse.
Note:
If you using a special mouse, suggesting to
install the mouse driver from original
manufacturer in order to manifest the
functionality of KVM Switch.
Q3 :
The mouse is out of control.
A3 : The mouse characteristic is inefficient. Try
another superior mouse and plug it back again.
Starting the operation when hearing the beep
sound.
Q4 :
There has the video problem.
A4 : The resolution or bandwidth is set too high.
KVM Switch supports the VGA, SVGA,
Multisync and XGA (interlaced) with the
resolutions up to 1920 x 1440 Hz. The
maximum bandwidth is 200 MHz
Q5 :
Why the LEDs reveal the green is on/ red is
flashing under PCs are turned off?
A5 : It’s normal state. The causes come from PC
internal setting. It shows the keyboard and/or
the mouse possesses the power.
-4-
Safety Information:
This device may only be operated in enclosed, dry
rooms. To prevent the risk of fire or electrical shock,
the device must be protected from moisture. In the
event of a defective power plug, please contact an
authorized retailer. In the event of damage to the
housing or the power plug, do not operate. Do not
open the device. Repairs may only be performed by an
authorized retailer.
Note:
In the event of incorrect installation and improper use
in a residential area, the device may cause disruptions
in radio devices and other electronic devices. Proper
use means that the device is operated with shielded
connector cables as far as possible, for network
products also with shielded cables of category 5e and
higher. The device was tested and lies within the limits
for computer accessories of class A according to the
requirements of EN 55022.
Warning:
This is a class A device. This device can cause radio
interference in residential areas; in this case, the
operator may be required to perform and bear the
costs for appropriate measures.
Conformity Declaration:
The device fulfils the EMC requirements of EN 55022
class A for ITE and EN 55024. Devices with external or
built-in power supply also fulfil the requirements of EN
61000-3-2 and EN 61000-3-3. The basic protection
requirements of the “EMC Directive” 89/336/EEC are
therefore fulfilled. The CE conformity has been
certified. The corresponding declarations are available
from the manufacturer.
Trademarks:
All company, brand and product names used in these
instructions are trademarks or registered marks of the
corresponding companies.
-5-
