Digitrax SE74 Manual Download Page 11

© 2022 Digitrax, Inc.

www.digitrax.com

— 11 —

not allow for Lunar lamps. OPSW35 polarity sets RED/GREEN choice.

6.  Be sure to set LED polarity/type: OPSW33/34/35 to your actual signals.
7.  The SE74 is setup to drive LEDS only, using external customer current set

-

ting resistors with about 5 volt unloaded drive levels.

8.  For more signaling accessories and more information, see the Signaling 

section of the 

www.digitrax.com web site.  If you need larger images, color or 

text, reference the pdf of these instructions on the web site.

8.0 Setup Notes:  

The SE74 manages turnout voltages and current. 

1. 

In pulse solenoid mode; for problem solenoids, try OPSW16=C for higher 

current Capacitive Discharge pulse action. 

2.  In all modes a 12-14V DC 0.3A supply should suffice, depending on the Sig

-

nal head brightness setting. 

3.  If you operate a SE74 with just DCC track power on TKA/TKB terminals, it 

will not have all features available.

4. 

For 2-wire pulse solenoids, e.g. a Kato N-crossover, just wire to R/G termi

-

nals in the polarity that operates as you need.  Do not run more than one 

solenoid device per SE74 pulsed R/G output pair.

5.  The combined  Static turnout/Lamp and Signal mast loads should set less 

than 0.30A draw on the DC input.  For Slow motion turnouts the total 

current per output R/G pair ON should draw less than 0.05A referred to DC 

input plug.

6.  Take care not to short any of the SE74; SE1 cables, R/G Outputs and P+ 

leads, or connect to other voltages like DC, Track power etc.  This may cause 

damage not covered by Warranty.

7.  If the SE74 flashes the "Ident" pattern of ID & RTS LEDs alternating with 

OPS LED  for 3 seconds it has detected an overload and has shutdown P+ 

voltage. Identify the overload and fix this before resuming operation.

8. 

The Digitrax original SE1 cable design has the multiplex symmetrical so the 

A/D and B/C masts can be rotated and alternately tested in a single socket. 

FIGURE 8: A/D direction Dual 2-wire searchlight heads 

FIGURE 9: B/C direction Dual 2-wire searchlight heads 

Summary of Contents for SE74













Reviews: