Digitrax SE74 Manual Download Page 10

© 2022 Digitrax, Inc.

www.digitrax.com

— 10 —

2.  These six wiring diagrams show how to connect the signal LED leads you 

have into a SE1 cable to display LED aspects. 

SE74 defaults support the 

provided Digitrax test mast with no OPSW changes needed.

3.  Figure 4 shows a PCB test mast with; two 3-color G type heads, 100 ohm 

current-setting resistors and 10-pin plug.  This mast is used for test and 

debugging the operation of SE74 A1/A2 (Dwarf) heads. Rotated 180 degrees 

on the cable this test mast acts like Figure 5; as B/C signal heads on any 

SE1 cable.  The test mast is wired for common anode operation as shown in 

Figure 4. 

The lunar LEDS are shown for wiring detail, and are not installed 

on the PCB test mast

.

4. 

The 3-wire Searchlights of Figures 6 and 7 are common cathode version and 

allow Lunar lamps to be connected for all 4 heads on an SE1 cable. 

5.  The 2-wire searchlight examples in Figures 8 and 9 need OPSW33 =C and do 

D/ A2: Diverging

Dwarf

A1 Mainline

D Lunar

A1 Lunar

Common Anode

FIGURE 4: Test Mast Dual 3 color heads with lunars

Mast Base PCB

common anode/OPSW35 =T

D/ A2: Diverging

Dwarf

A1 Mainline

D Lunar

A1 Lunar

FIGURE 6: A/D direction Dual 3-wire searchlight heads with lunars

common cathode/OPSW35 = C

B Mainline

C Siding

B Lunar

C Lunar

Common Anode

FIGURE 5: B/C direction Dual 3 color heads with lunars

Mast Base PCB

common anode/OPSW35 =T

B mainline

C Siding

B Lunar

C Lunar

FIGURE 7: B/C direction Dual 3-wire searchlight heads with lunars

common cathode/OPSW35 = C

Summary of Contents for SE74













Reviews: