manualshive.com logo in svg

Digital Knight DK14S, Manual

Share
Download
Digital Knight DK14S Manual Download Page 9

9

ERR Mode

During. operation. of. the. press,. if. there.
is.a.loss.of.signal.from.the.temperature.
sensor. wire,. the. ERR. display. will.
appear.

This.is.a.safety.feature.that.will.shut.off.
the.relay.so.the.press.will.not.overheat.
aimlessly.without.a.temperature.signal.

Once.the.temperature.signal.is.restored.(no.longer.broken,.or.plugged.
back.into.the.control).the.press.will.resume.the.temperature.display,.and.
start.heating.if.necessary..If.ERR.persists,.contact.support.

Over-Temp Alarm

If. the. press. heats. beyond. the. set.
temperature. by. 40. degrees. or. greater,.
the.OverTemp.alarm.will.sound.

This. is. a. safety. feature. that. warns. the.
operator.of.a.possible.thermal.run-away.
of.the.press..This.means.the.press.relay.
may. be. locked. in. a. heating. position.
where. it. will. never. stop. heating,. to. a.
possibly.harmful.temperature.level.

If.the.OverTemp.alarm.sounds,.set.the.temperature.to.a.higher.value.
than.the.current.actual.temp..Wait.30.seconds.and.then.reset.the.press.to.
your.desired.temperature.and.Watch.Carefully..Do.not.let.the.press.rise.
to.extremely.high.temps.

If. it. continues. to. rise,. turn. off. the. press. and. let. it. cool. off. to. room.
temperature..Turn.the.power.back.on.and.immediately.set.the.temperature.
to.a.low.setting.like.200°F..Wait.for.the.press.to.heat.up..When.the.press.
displays.“READY”,.monitor.the.temperature.and.see.if.it.continues.to.
heat.to.a.level.that.the.OverTemp.alarm.activates.again..If.so,.contact.
the.factory.

Summary of Contents for DK14S

























Reviews:

No comments

Brands by name

Popular brands

Load more brands