background image

iii

Contents

Introduction  

  1

Tools Needed ................................................................................................... 1
Kit Contents ..................................................................................................... 2
Enable the Onboard VGA Controller................................................................ 2

Update Your BIOS                                                                      3

Power Down the Server  ................................................................................... 3
Remove any Video Option Card ....................................................................... 3
Check the Jumper Settings  .............................................................................. 4
Replace the Panel and Reconnect the Cables .................................................... 5
Power Up the Server and Update Your BIOS ................................................... 5
Reset Jumpers on the Main Logic Board .......................................................... 6

Powergrade Installation                                                            6

Remove the CPU Module  ................................................................................ 6
Install a Second CPU Chip (Kits FR-PC97U-AA, -AF Only)  ..........................  8
Install the Secondary Cache.............................................................................. 9
Check the Jumper Settings  ............................................................................  10
Install the Voltage Regulator Module  ............................................................  11
Install the CPU Module  .................................................................................  11
Install the New Medallion  .............................................................................  12
Replace the Panel and Reconnect the Cables ..................................................  12

Run the System Configuration Utility (SCU)                          12

Troubleshooting                                                                       13

Using the Crisis Recovery Diskette  ................................................................. 13
Bulletin Board Access  .................................................................................... 13

Summary of Contents for Prioris XL 5166


















Reviews: