Digikeijs DR4024 Instruction Manual Download | Manualshive

Page: 25 / 25

background image

DR4024 Servodecoder

P 25

www.digikeijs.com

® R-Bus, B-Bus

are trademarks which are registered in the name of Modelleisenbahn GmbH. XpressNet and RS-Bus is a trademark registered in the name of Lenz

Stand 2018.10.22

Let your imagina1on run wild by using the presets as a star1ng point on which to build other eﬀects. For example, you can use preset 2 as the basis for a signal that
inﬂuences the behavior of the locomo1ve: Adjust the func1on mapping so that the outputs switch together with the servos and set the output conﬁgura1on so that
it switches when the green mode is reached.

Important: The servo speed and end posi1ons are not inﬂuenced by the presets!

Default seBng 3 (Preset 3)
Level crossing with changeable indicators,
two barriers and mass simula1on

«
...
23
24
25

Summary of Contents for DR4024


























Reviews:

No comments

Related manuals for DR4024

Brand: YMGI Pages: 64

Brand: Thinkpower Pages: 30

Brand: ESI Pages: 17

Brand: HEIDENHAIN Pages: 6

Brand: 3onedata Pages: 3

Allen-Bradley 842D

Brand: Rockwell Automation Pages: 58

ALL-USB-RS422/485

Brand: Allnet Pages: 6

I/O SYSTEM FIELD 765-2704/200-000

Brand: WAGO Pages: 42

Brand: Patton electronics Pages: 7

Brand: Sencore Pages: 126

Brand: StarTech.com Pages: 4

Brand: Actox Pages: 36

Brand: Morningstar Pages: 16

Brand: Datavideo Pages: 23

LOUDSPEAKER SP100

Brand: Sonos Pages: 46

Brand: Shinybow USA Pages: 2

SitePlayer Telnet Series

Brand: NetMedia Pages: 52

Brand: SIIG Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands