Digicom SNM70 User Manual Download Page 12

Description

3.3

S

READ/WRITE A REGISTER

Sn=x

Write value x to S Register n.

Sn?

Read value at S Register n.

V

VERBOS RESULT CODE

V0

Result code display as digit (short form).

V1

Result code display as words (extention form).

RESULT CODE SHORT & EXTENDED FORM SUMMARY

SHORT

EXTENDED

0

OK

1

CONNECT

2

RING

3

NO CARRIER

4

ERROR

5

CONNECT 1200

6

NO DIALTONE

7

BUSY

8

NO ANSWER

10

CONNECT 2400

11

CONNECT 4800

12

CONNECT 9600

13

CONNECT 7200

14

CONNECT 12000

15

CONNECT 14400

16

CONNECT 19200

17

CONNECT 38400

19

CONNECT 115200

22

CONNECT 1200TX/75RX

23

CONNECT 75TX/1200RX

40

CARRIER 300

44

CARRIER 1200/75

45

CARRIER 75/1200

46

CARRIER 1200

47

CARRIER 2400

48

CARRIER 4800

49

CARRIER 7200

50

CARRIER 9600

51

CARRIER 12000

52

CARRIER 14400

53

CARRIER 16800

54

CARRIER 19200

55

CARRIER 21600

56

CARRIER 24000

57

CARRIER 26400

58

CARRIER 28800

78

CARRIER 31200

79

CARRIER 33600

66

COMPRESSION: CLASS 5

67

COMPRESSION: V42 bis

69

COMPRESSION: NONE

76

PROTOCOL: NONE

77

PROTOCOL: LAPM

80

PROTOCOL: ALT

150

CARRIER 32000

151

CARRIER 34000

152

CARRIER 36000

153

CARRIER 38000

154

CARRIER 40000

155

CARRIER  42000

156

CARRIER 44000

157

CARRIER 46000

158

CARRIER 48000

159

CARRIER 50000

160

CARRIER 52000

161

CARRIER 54000

162

CARRIER 56000

165

CARRIER 32000

166

CARRIER 34000

167

CARRIER 36000

168

CARRIER 38000

169

CARRIER 40000

170

CARRIER 42000

171

CARRIER 44000

172

CARRIER 46000

173

CARRIER 48000

174

CARRIER 50000

175

CARRIER 52000

176

CARRIER 54000

177

CARRIER 56000

Note: The commands in the above list

can be followed by \ARQ message

SHORT

EXTENDED

SNM7003.pm6

4/8/98, 14:46

3

Summary of Contents for SNM70




























Reviews: