Digi XBee RR Hardware Reference Manual Download

Page: 25 / 67

Specifications

Serial communication specifications

Digi XBee® RR RF Module Hardware Reference Manual

Serial communication specifications

The XBee RR RF Module supports Universal Asynchronous Receiver / Transmitter (UART) and Serial
Peripheral Interface (SPI) serial connections.

UART pin assignments

UART pins

Device pin number

Micro-mount

DOUT/DIO13

DIN / CONFIG/DIO14

CTS / DIO7

RTS/ DIO6

SPI pin assignments

GPIO specifications

XBee RR RF Modules have 15 General Purpose Input / Output (GPIO) ports available. The exact list
depends on the device configuration as some GPIO pads are used for purposes such as serial
communication.

GPIO electrical specification

Value

Input pull-up resistor value

40 k

(typical)

Input pull-down resistor value

40 k

(typical)

Output voltage for logic 0

0.2 x VCC (maximum)

Output voltage for logic 1

0.8 x VCC (minimum)

Output source/sink current

50 mA (maximum)

Total output current (for GPIO pads)

200 mA (maximum)

Electro Static Discharge (ESD)

XBee RR RF Module pins are tolerant to human-body model ± 1.5 kV.

Note

Take care to limit all electrostatic discharges to the device.

Summary of Contents for XBee RR




































































Search results

Summary of Contents for XBee RR

Reviews:

Related manuals for XBee RR

Brands by name

Popular brands

Digi XBee RR, Hardware Reference Manual

Search results

Summary of Contents for XBee RR

Reviews:

Related manuals for XBee RR

Brands by name

Popular brands