background image

 

Doc #:90000070  Rev. C

 

Legal

 

Trademark Rights

 

Digi International™, FastPort™, Print Server Software™, and the Digi logo are trademarks of

 

 Digi International, Inc

 

. All other 

brand and product names are the trademarks of their respective holders.

© Digi International, 1998. All Rights Reserved.

Information in this document is subject to change without notice and does not represent a commitment on the part of Digi 
International.

Digi International provides this document “as is,” without warranty of any kind, either expressed or implied, including, but not 
limited to, the implied warranty of fitness or merchantability for a particular purpose. Digi International may make 
improvements and/or changes in this manual or in the product(s) and/or the program(s) described in this manual at any time.

This document could include technical inaccuracies or typographical errors. Changes are periodically made to the information 
herein; these changes may be incorporated in new editions of the publication.

 

Restricted Rights

For non-U.S. Government use

 

These programs are supplied under a license. They may be used, disclosed, and/or copied only as permitted under such license 
agreement. Any copy must contain the above copyright notice and this restricted rights notice. Use, copying, and/or disclosure 
of the programs is strictly prohibited unless otherwise provided in the license agreement.

 

For U.S. Government use

 

Use, duplication, or disclosure by the Government is subject to restrictions as set forth in sub-paragraph (c)(1)(ii) of the Rights 
in Technical Data and Computer Software clause of DFARS 52.227-7013.

 

The Digi Five-Year Limited Warranty

 

Digi International warrants to the original consumer or purchaser that each of its products, and all components thereof, will be 
free from defects in material and/or workmanship for a period of five years from the original factory shipment date. Any 
warranty hereunder is extended to the original consumer or purchaser and is not assignable.

Digi International makes no express or implied warranties including, but not limited to, any implied warranty of 
merchantability or fitness for a particular purpose, except as expressly set forth in this warranty. In no event shall Digi 
International be liable for incidental or consequential damages, costs, or expenses arising out of or in connection with the 
performance of the product delivered hereunder. Digi International will in no case cover damages arising out of the product 
being used in a negligent fashion or manner.

 

Regulatory Approvals

 

FCC Class A

UL 1950

CSA 22 No. 950

EN60950

CE
– EN55022 Class B
– EN50082-1

 

Canadian EMI Notice

 

This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

 

European Notice

 

Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) 
issued by the commission of the European Community. Compliance with these directives implies conformity to the following 
European Norms:

EN55022 (CISPR 22) - Radio Frequency Interference

EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic Immunity

EN60950 (IEC950) - Product Safety

 

To Contact Digi

 

For prompt response when calling for service information, have the following information ready:

Product serial number

Date of purchase

Vendor or place of purchase

You can reach Digi LAN technical support at 408/744-2751 or 

 

[email protected]

Summary of Contents for FastPort MIL-3100FTX































Reviews: