Digga TPE-000039 Operator'S Manual Download Page 10

10

PM-000134  - Telescopic Piling and Drilling Extension Operators Manual - September 2015

4       SAFETY PRECAUTIONS - GENERAL INFORMATION

MAINTAINING THE TELESCOPIC PILING AND DRILLING EXTENSION

•  Before performing maintenance, lower the attachment to the ground, apply the parking brakes, turn off the 

engine, and remove the key. 

•  Drill rigs must be shut down and properly locked-out and tagged before repairs or maintenance is per-

formed. Only properly trained and qualified individuals are permitted to perform repairs and maintenance.

•  Never adjust a relief valve for pressure higher than recommended by the machine’s manufacturer.

WARNING

WARNING

TRANSPORTING

Follow all local government regulations that may apply along with recommended tie down points and any 
equipment safety precautions at the front of this handbook when transporting your attachment.

TIE DOWN POINTS

•  Tie down points are identified by tie down decals where required. Securing to trailer at other points is unsafe 

and can damage attachment. 

•  Do not attach tie down accessories around cylinders or in any way that may damage hoses or hydraulic 

components.

•  Attach tie down accessories to unit as recommended.
•  Check unit stability before transporting.

Verify that all tie down accessories (chains, slings, ropes, shackles and etc.) are capable of maintaining attach-
ment stability during transporting and are attached in such a way to prevent unintended disengagement or shifting 
of the unit. Failure to do so could result in serious personal injury or death. 

GROUND PERSONNEL AND BYSTANDERS 

•  Be alert to others in the work area. Be sure others know when and where you will be working. Make sure no 

one is behind equipment or within 20ft (6m) of it operating. 

•  Loose fitting clothing, long hair, jewellery and equipment which might become entangled in moving equipment 

are prohibited while working near Telescopic Piling and Drilling Extension.

•  Operators, helpers, and other personnel working near the Telescopic Piling and Drilling Extension must wear 

steel-toe safety shoes, safety glasses, and hard hats as a minimum. Hearing protection, respirators, and 
personnel protective clothing will be specified in the site-specific Health and Safety Plan.

WARNING

WARNING

Summary of Contents for TPE-000039
























Reviews: