Diatron ABACUS 4 Service Manual Download Page 53

Page: 53 / 62

Abacus

Service Manual

6.5.2. Abacus4 message code list

Code

Message text

5001

Remove reagent tubing at rear reagent inputs (Diluent, Lyse, LyseEOS and
Cleaner). Leave waste connected.

5002

Connect min. 100 ml distilled water to reagent inputs using cleaning tube kit.

5003

Remove cleaning tube kit. Keep reagent inputs free.

5004

You can power off the system!

5005

Apertures are partially clogged. Try cleaning!

5006

Please empty waste container!

5101

%u data record(s) is selected.

5102

Insert data disk!

5106

No such type of data

5200

New reference ranges will be saved. Press OK to confirm.

5300

Some or all of the calibration factors are out of range!

5400

+12V too low!

5401

+12V too high!

5402

Battery voltage too low!

5901

Insert software update USB drive!

The system will restart!

5902

Are you sure to delete all device statistics?

5903

This function will delete all measured results.

Are you sure?

5904

This function will delete all selected records.

Are you sure?

5905

Are you sure %s?

5906

Now it is safe to turn the instrument off...

5907

Now it is time to clean the washing head with a damp cloth, and check the pump
cleanliness. Make sure they are all clean, then you can proceed.

5908

Set the needle and press OK to continue!

Summary of Contents for ABACUS 4































































Search results

Summary of Contents for ABACUS 4

Reviews:

Brands by name

Popular brands

Diatron ABACUS 4, Service Manual

Search results

Summary of Contents for ABACUS 4

Reviews:

Brands by name

Popular brands