Diatron ABACUS 4 Service Manual Download Page 52

Page: 52 / 62

Abacus

Service Manual

Code

Error text

Reason(s)

Remedy

1401

Printer error. Check paper!

Printer is out of
paper and there are
some other printer
errors!

Feed the printer with paper. Check the
connections between the instrument and
the printer and check the printer setup in
the Settings/Printer settings sub-menu.

1402

Printer is out of paper! Check
paper!

Printer is out of
paper!

Feed the printer with paper.

1403

Printer was not set up correctly The selected printer

type does not match
to the printer!

Modify the printer setup in the
Settings/Printer settings sub-menu.

1405

Paper height is too large

Paper height
overstep the
margin!

Modify the paper setup in the
Settings/Printer settings sub-menu.

1411

Error #%d in printer
initialization!

Printer software
error!

Check the connections between the
instrument and the printer and check the
printer setup in the Settings/Printer
settings sub-menu.

Try to make a software upgrade.

1900

You have to add at least one
user to use multi user mode!

Multi-user
problem.

Follow the instruction, or change to single
user mode in the User settings submenu.

1921

%s sensor calibration failed!
The system turned off the %s
sensor.

Reagent container
became empty, or
there are lot of
bubbles in reagent
tubes.

Replace the reagent container with a filled
one.

If this is still a problem with a filled
reagent container, turn on the sensor
and try recalibrating and check the
tubings and the fittings.

Summary of Contents for ABACUS 4































































Search results

Summary of Contents for ABACUS 4

Reviews:

Brands by name

Popular brands

Diatron ABACUS 4, Service Manual

Search results

Summary of Contents for ABACUS 4

Reviews:

Brands by name

Popular brands