DiaSys O-Classic Operator'S Manual Download

Page: 6 / 29

2.5 D

ESCRIPTION

THE

CONTROL

UNIT

Terms meaning:

Pump

: pump

Flush

: rinsing

Source

: water supply

Full

: full storage tank

Power

: switched on

Washing

: manual rinsing

PUMP light ON

Pump working: the water purifier is producing or rinsing.

FLUSH light ON

The water purifier is automatically rinsing the reverse osmosis
membrane. A rinsing (around 2 mins) happens when :

- the machine is starting up
- every 6 hours

- after pushing the WASHING button.

SOURCE light ON

Lack of flowrate or pressure on the water supply.

FULL light ON

Full storage tank.

POWER light ON

Water purifier switched ON: this light is always ON, whatever the

state of the other lights.

WASHING button

Pushing this button launches a membrane rinsing during around 2

mins.

CONDUCTIVITY ALARM light

Informs you about the water conductivity.

Water purifier producing

Water purifier rinsing

Lack of water supply

Full storage tank

Produced water conductivity

1µS/cm

Produced water conductivity 1µS/cm

5µS/cm

Produced water conductivity > 5µS/cm

O-Classic

operator’s manual

version: 20.01.22

Summary of Contents for O-Classic






























Search results

Summary of Contents for O-Classic

Reviews:

Related manuals for O-Classic

Brands by name

Popular brands

DiaSys O-Classic, Operator'S Manual

Search results

Summary of Contents for O-Classic

Reviews:

Related manuals for O-Classic

Brands by name

Popular brands