background image

_________________________________________________________________________ use and instruction 

manual _ 

_ page 10 

________________________________________________________________________________________ 

7. Instructions for use 

COOK-TOP 

-

Cook-top control panel and use

 - On the control panel, 4 

empty and one fully coloured circles are placed next to each 
gas cock knob of the cook-top (Fig. 6). The fully coloured one 
indicates the position of the gas burner that is commanded by 
the knob in question. 

 

Fig. 6 

-

Electric lighting of the burners with safety device

 - The 

cook-top is equipped with electric ignition of the burners by 
means of spark plug “A” (Fig. 7). The spark plug operates when 
the push-button on the control panel is pressed. This button is 
marked by symbol 

 (spark). To ignite the burner press the 

electric ignition push-button and, at the same time, press and 
turn in an anticlockwise sense the knob of the burner that is to 
be started to the symbol 

 (large flame/ignition spark). 

Release the electric ignition push-button once the flame has 
appeared and keep the gas cock knob pressed for about 6 - 8 
sec., so as to let the safety thermocouple “B” heat-up. Release 
the knob and turn it to the position desired.

 

 

Fig. 7 

 

Should the flame die-out, the safety thermocouple “B” will intervene automatically and 
close the gas cock, thus blocking the gas flow to the respective burner. 
To re-ignite the burner, turn the knob to the 

 (off) position and repeat the ignition 

operations after having waited for approximately 1 minute. Each burner can operate at 
either maximum or minimum level or at intermediate levels by setting the knob anywhere 
between the maximum and minimum positions. 
 
The various positions of the gas cock knob are indicated as follows: 

position off 

 

position for maximum 

  (large flame/ignition spark) 

position for minimum 

 (small 

flame) 

 

Warning - The pots used on the cook-top burners should not have a concave or convex 
base but rather, a full base (Fig. 8). They should have the following minimum diameter: 

 

 

Mod. CV5P – CV5P5 

180 mm for the ‘semi-fast’ burner (front right burner); 

220 mm for the “fast” burner (back left-right burner; front left); 

240 mm for the ‘triple crown’ burner (central burner).

 

 

 

Mod. CV5E-90 A – CM5E-90 A – CV2R 

180 mm for the ‘semi-fast’ burner (back right burner); 

220 mm for the “fast” burner (back left burner ; front left-right); 

240 mm for the ‘triple crown’ burner (central burner). 

 

Summary of Contents for C5FV6



















Reviews: