manualshive.com logo in svg

Diamond Products CPG80E, Operator'S Manual

Share
Download
Diamond Products CPG80E Operator'S Manual Download Page 20

 

 

MAINTENANCE 

Tensioning the Drive Belts 

1.  Using a 9/16” wrench, loosen the four 

motor mounting bolts on the motor base. 

 

Motor Mounting Bolts

 

2.  Using a 1/4” hex drive, turn the drive belt 

tensioning bolt clockwise to tighten or 
counter-clockwise to loosen the belts. 

 

Drive Belt Tensioning Bolt 

3.  Tension the belts as required and retighten 

the four motor mounting bolts on the motor 
base. 

Replacing the Drive Belts 

WARNING 

De-energize the power to the floor 
grinder  by  unplugging  the  power 
cord prior to removing V-belts 

 
 

1.  Remove the four 1/4”-20 flat head cap 

screws from the pulley shield. 

2.  Remove the pulley shield. 

 
 

 

Pulley Shield 

3.  Using a 9/16” wrench, loosen the four 

motor mounting bolts on the motor base. 

 

Motor Mounting Bolts 

4.  Using a 1/4” hex drive, turn the drive belt 

tensioning bolt counter-clockwise and push 
the motor forward to loosen the belts. 

 

Drive Belt Tensioning Bolt 

20

Summary of Contents for CPG80E





























Reviews:

No comments

Brands by name

Popular brands

Load more brands