manualshive.com logo in svg

Dialogic BN500IP, Installation And Configuration Manual, Page: 18 / 46

Share
Download
Dialogic BN500IP Installation And Configuration Manual Download Page 18

Dialogic

®

 BorderNet

™

 500 Gateways Installation and Configuration Guide

Page 18 

• If you answer n, nothing is removed. 
• If  you  answer  y, you have three update modes to select from: 

1

Clear as little as possible. This is the alternative that is used if you answer n to the question above. 
Both the preliminary configuration and the permanent configuration will be updated with the 
configuration specified above. 

2 Revert to the factory configuration and apply the configuration specified above. This will affect the 

permanent configuration, but not the preliminary configuration. 

3

Revert to the factory configuration, empty all logs, and apply the configuration specified above. Both 
the preliminary configuration and the permanent configuration will be affected. 

9. Select one of the three update modes described above. 

The configuration is now complete. The installation program shows the configuration and asks if it is correct. 
• yes saves the configuration. 
• no runs the installation program over again. 
• abort ends the installation program without saving.  

10. Finish configuration of the BorderNet 500 Gateway from the computer/computers specified in the installation 

program. 

Turning Off a Dialogic

® 

BorderNet

TM 

500 Gateway 

To turn off a BorderNet 500 Gateway, turn the computer off. The computer that runs the software is specially 
designed so that you can switch it off without causing any problems in the file structure. 

Locking Up a Dialogic

® 

BorderNet

TM 

500 Gateway 

The BorderNet 500 Gateway must be protected from unauthorized physical access just as other computers 
performing critical tasks. A locked up BorderNet 500 Gateway protects against: 

• Connecting to the console 
• Changing the administrator password using a reboot and the BorderNet 500 Gateway buttons. 

For more information about the necessary configuration, see 

Tasks for Installing and Configuring a Dialogic

®

 

BorderNet™ 500 Gateway

 on page 13. 

Update mode (1-3) [1]:

You have now entered the following configuration 

Network configuration inside: 
Physical device name: eth0 
IP address: 192.168.150.2 
Netmask: 255.255.255.0 
Deactivate other interfaces: no 

Computer allowed to configure from: IP address: 192.168.128.3 

Password: eeyore 

The rest of the configuration is kept. 

Is this configuration correct (yes/no/abort)? yes

Summary of Contents for BN500IP















































Reviews:

No comments