Dialog DA16200 User Manual Download Page 18

 

 

      

 

DA16200 AT GUI Tool 

  

User Manual 

Revision 1.0 DRAFT 

03-Jul-2019 

CFR0012 

18 of 20 

© 2020 Dialog Semiconductor 

4.1.4 

Manual Information to the End User  

The OEM integrator has to be aware not to provide information to the end user regarding how to 
install or remove this RF module in the user’s manual of the end product which integrates this 
module.  

4.2 

Canada Statement  

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the 
following two conditions: (1) this device may not cause interference, and (2) this device must accept 
any interference, including interference that may cause undesired operation of the device. 
  
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio 
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit 
pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique 
subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 
  

4.2.1 

Caution Exposure: 

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS102 and 
users can obtain Canadian information on RF exposure and compliance. 
Le dispositif répond à l'exemption des limites d'évaluation de routine dans la section 2.5 de RSS102 
et les utilisateurs peuvent obtenir des renseignements canadiens sur l'exposition aux RF et le 
respect. 
  
  
  

4.2.2 

The final end product must be labelled in a visible area with the 
following:       

The Industry Canada certification label of a module shall be clearly visible at all times when installed 
in the host device, otherwise the host device must be labelled to display the Industry Canada 
certification number of the module, preceded by the words “Contains transmitter module”, or the word 
“Contains”, or similar wording expressing the same meaning, as follows:   
Contains transmitter module IC: 25650-DA16200MC, or 25650-DA16200ME. 
  
The module must be installed in WiFi Module. 
  
This End equipment should be installed and operated with a minimum distance of 20cm between the 
radiator and your body. 
  
Cet équipement devrait être installé et actionné avec une distance minimum de 20cm entre le 
radiateur et votre corps. 
  
The end user manual shall include all required regulatory information/warning as show in this 
manual. 

 

Summary of Contents for DA16200





















Reviews: