DIAKAT RK-10 Operator'S Manual Download Page 4

 
 

 

 
 

RK10

RK10

RK10

RK10S

S

S

S

   Roofing saw

 

Page 3 of 8 

1.14. Using the machine 

 
When using the machine the operator must comply with the following instructions: 
 

1. Check the machine before use. 
 
2. Before commencing work check if it is safe to start the machine with out endangering 
the operator or other persons. 
 
3. Use prescribed personal safety aids while  working. (Helmet, earmuffs, safety shoes, 
goggles, respirator, gloves…). 
 
4. Do not start the machine in enclosed area. 
 
5. While working monitor the machine for unusual sounds or smoke which may indicate 
defect.  When  defect  is  indicated  immediately  stop  the  machine  and  call  for  expert 
repair. 
 
6. Always switch off the engine when refuelling. Take care that the fuel does not come 
into contact with hot parts of the engine. Wipe out immediately any spillage.  
 
7. !ATTENTION! It is important to immediately repair or change improperly sealed or 
leaky fuel tank and lines. Improperly sealed or leaky fuel tank and lines may cause an 
explosion.  
 
8. It is necessary to provide an adequate supply of fresh air for the operator, when using 
the machine in enclosed areas (tunnels etc.). 
 
 9. When finish working, switch off the engine and move the machine the secure place 
and insure against unauthorized use. 

 
 

1.1.5.

 

Checkups, maintenance, service and repair  

 

 

regularly check the technical state of the machine. 

 

if fault or damage is discovered ensure expert repair.  

 

repair  or  service  may  bee  carried  out  only  by  qualified  personnel  from  a 
manufacturer’s service organisation. 

 

it  is  prohibited  to  carry  repairs  or  service  at  places  where  the  safety  of  work  is  not 
ensured and can be affected by outside impingement, such as falling objects, collision 
with other machinery etc.  

 

  changes  and  alteration  to  the  machine  can  be  carried  out  only  with  the  explicit 
agreement of the manufacturer! 

 

1.2.

 

Transporting the machine  

 
1. Always transport the machine in a secured position 
on its transport wheels. 
 
2. When transporting secure the machine against   
overturning, moving or falling off. 
 
3. Never transport the machine with the engine running! 

 
 
 
 
 

Summary of Contents for RK-10










Reviews: