background image

Introduction

Thank you for choosing

 DHK's HUNTER!

 

This short course truck(SCT) is designed in thorough research

 and assembled with utmost craftsmanship. Hunter is a 1:10 sclale 4WD brushed SCT can run as fast as
 22MPH/35KPH. It is easy to drive and it uses quality parts and accessories to achieve best performance.

 It will bring you a lot of joy and fun when you drive this model.

Before starting to run the model, you are kindly requested to take some time to review this instruction
manual for a better operation. This easy to follow instruction manual aims to provide a general guideline

for end-users. Kindly note that a good understanding of the model, its relevant parts together with other

accessories packed in this consumer box will enable you to have fun in driving. Meanwhile, users are

recommended to conduct regular maintenance for a smooth performance. Failure to do so might shorten

the lifespan of your model. You are cordially advised that DHK Hobby makes all necessary parts and

accessories to support you for any problem during and after your driving.

Before you operate this radio controlled model, you must understand the following:

1. Make sure that all screws and nuts are tightened securely.
2. Make sure that the batteries are fresh or fully charged so the vehicle won't lose control.
3. Do not drive the model in the following places/areas to avoid injury of people and damage to the

public property. Drive your model in open areas.

>   On public streets or parks. Cause injury or death of pedestrians, young children, animals and pets. 
>   On highways. Cause accidents or damage of the model. 

>   In water. Cause damage to electronic components and parts, or direct failure of the model.

4. Check all signals and electronic parts are working properly. 

After running, battery, ESC, and motor can be very hot. Make sure not to touch with bare hands.

           Warning:

This high performance model can run very fast. It is designed and produced for people of 14+ years of 
age to operate. Players under that age should be guided by adult supervision. Entry level players should 
seek guidance and supervision from experienced model players. Players are responsible for any/all 
accidental occurrences (human or animal injury, damage to property and possessions, breakage of the 
model itself) due to improper operation of this model.  

Summary of Contents for HUNTER 8135





























Reviews: