DGFLOW DGB MV 30, Operator And Maintenance Manual

Page: 10 / 40

10
CHECKING THE DIRECTION OF ROTATION OF THE MOTOR (PUMP 1 ROTATION)
For surface pumps
(see fig. below): switch the system to TEST mode, start it by pressing START, and look to
see whether the motor fan is turning in the direction indicated on the pump body. Stop the system by pressing
STOP.
START
STOP
3 0.
0 HZ
2 .7 A
41 0 V
1 5 :0 2 0 4 /11 /2 01 1
P 3 .2
TEST 1
TEST
1 TEST
P 0 .0
0 4 /11 /2 0 11 15 :0 2 1 5 :02 0 4 /1 1 /20 1 1
set 4 .0 Bar
P 0 .0
1 2
SYSTEM
OFF STOP
1 TEST
P 0 .0
0 4 /11 /2 0 11 15 :0 2
START
STOP
STOP OFF
SYSTEM
2 1
P 0 .0
set 4 .0 Bar
0 4 /1 1 /20 1 1 1 5 :02
ESC
If the direction of rotation does not coincide, switch it over by means of the PUMP 1 ROTATION parameter (see
fig.below).
ESC
SET
1
MAINTENANCE
HARDWARE SETUP
ADV SETUP
BASE SETUP
MAIN MENU
ESC
ESC
DIRECT
SERIAL - FIIRMW
1.4
PRESSURE SET 1
PRESSURE SET 2
PUMP 1 CURRENT
PUMP 1 ROTATION
BASE SETUP
BASE SETUP
PUMP 1 ROTATION
PUMP 1 CURRENT
PRESSURE SET 2
PRESSURE SET 1
1.4
SERIAL - FIIRMW
DIRECT
DIRECT
SERIAL - FIIRMW
1.4
PRESSURE SET 1
PRESSURE SET 2
PUMP 1 CURRENT
PUMP 1 ROTATION
BASE SETUP BASE SETUP
PUMP 1 ROTATION
PUMP 1 CURRENT
PRESSURE SET 2
PRESSURE SET 1
1.4
SERIAL - FIIRMW
DIRECT
1
MAINTENANCE
HARDWARE SETUP
ADV SETUP
BASE SETUP
MAIN MENU 15:02 04/11/2011
set 4.0 Bar
P 0.0
1 2
SYSTEM
OFF
SERIAL - FIIRMW
1.1
PRESSURE SET 1
PRESSURE SET 2
PUMP 1 CURRENT
PUMP 1 ROTATION
BASE SETUP SET P.1
1.0-9.0
Bar
4.0
For submersible pumps
(see fig. below) the system must be placed in WORK mode; start the system by
pressing START, with a connected unit open; DGBOX will take the system pressure to that of set P1. Once
operating speed has been achieved, read and record the operating frequency to maintain the pressure of set
P1.
OFF
SY STEM
2 1
P 0 .0
set 4 . 0 Bar
0 4 / 1 1 / 2 0 1 1 1 5 : 0 2
4 1 0 V
2 .8 A
3 6 .
8 HZ
1 5 : 0 2 0 4 / 1 1 / 2 0 1 1
set 4 . 0 Bar
P 4 .0
1 2
1 2
STOP
START
Now reverse the direction of rotation by means of the PUMP 1 ROTATION parameter as indicated in the above
example for surface pumps, repeat the starting operation and again record the operating frequency to
maintain the SET pressure.
The correct direction of rotation is that which calls for the lesser frequency to maintain the
SET pressure.