20
Chapter 5
Chapter 5 Ports and Connectors
USB Ports
The USB device allows data exchange between your computer and a wide range of simultane-
ously accessible external Plug and Play peripherals.
The system board is equipped with one external USB 3.0 port (USB 0) and three external USB
2.0 ports (USB 2/6/7). In addition, it also has a 10-pin connector and allows you to connect
one additional USB 2.0 port (USB 5).
BIOS Setting
Configure the onboard USB in the Advanced menu (“USB Configuration” submenu) of the
BIOS. Refer to Chapter 7 for more information.
LAN 2
LAN 1
3
DDR3L
DDR3L
DDR3L
DDR3L
Mini PCIe with SIM
COM 4
RS232/RS422/RS485
12
10
3
1
JP22
1
1
1
(JP20)
(JP18)
(JP17)
(JP21)
1
3
12
10
COM 2
RS232/RS422/RS485
COM 1
RS232/RS422/RS485
USB 0
USB 3.0
HDMI
Reset
Power
39
40
2
1
LVDS LCD
Panel
USB 7
USB 6
Mic-in
1
Battery
Buzzer
1
Chassis
Intrusion
1
Clear CMOS
Data (JP24)
SPI
Flash
BIOS
eMMC
(optional)
iTE
IT8528E
Mini PCIe with LPC
mSATA
MicroSD
(optional)
1
System Fan
1
USB 0
Power
Select
(JP5)
1
2
5
6
(JP23)
1
1
1
(JP3)
(JP4)
1
2
10
9
COM 6
1
10
9
COM 5
1
1
USB 2 Power
Select (JP6)
USB 5-7 Power
Select (JP7)
1
2
10
9
USB 5
(JP25)
USB 2.0
USB 2.0
(JP17)
(JP20)
COM 4/DIO Select
(JP22, JP21)
Digital I/O 0-3 Output State
Digital I/O Power Select
Panel Power Select
(JP3)
(JP4)
(JP23)
Backlight Enable Power Select
Auto Power-on Select
(JP25)
Dimming Mode Select
(JP18)
Digital I/O 4-7 Output State
1
COM 3
RS232/RS422/RS485
4
1
(JP2)
(JP2)
LCD/Inverter Power Select
SATA 1
4
1
SATA
Power
1
SATA 2.0
I C
Line-out
DC-in
USB 2
USB 2
USB 2
USB 2
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the
+5V_standby power source of your power supply must support ≥1.5A. For 3 or more
USB ports, the +5V_standby power source of your power supply must support ≥2A.
Driver Installation
You may need to install the proper drivers in your operating system to use the USB device.
Refer to
Chapter 8 for more information.
Wake-On-USB Keyboard/Mouse
The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse
to wake up a system from the S3 (STR - Suspend To RAM) state. To use this function, you
must select voltage state for the USB ports via jumper settings.
Jumper Settings for the Wake-On-USB function
JP5, JP6 and JP7 must be set to “1-2 On: +5V_standby”. Refer to “USB Power Select” in the
previous chapter for more information.
USB 5
USB 2
USB 6
USB 7
USB 2.0
USB 0
USB 3.0
USB 2.0
1
2
10
9
VCC
-Data +Data GND
Ke
y
N.C.
N.C.
N.C.
N.C.
N.C.
