29
Chapter 2
HARDWARE INSTALLATION
User's Manual |
CMS631
Please follow the steps below to install the card into the socket.
Step 2:
Press the end of the card far
from the socket down until
against the stand-off.
Step 3:
Screw tight the card onto the
stand-off with a screw driver
and a stand-off screw until
the gap between the card and
the stand-off closes up. The
card should be lying parallel to
the board when it’s correctly
mounted.
Step 1:
Insert the card into the socket
at an angle while making sure
the notch and key are perfectly
aligned.
M.2 Module
M.2 Socket
Key
Stand-off
Notch
X
Internal I/O Connectors
X
Expansion Slots
1
M.2 E Key
2230
(Opt.)
M.2 M Key
M.2 M Key
DDR4_1
DDR4_2
DDR4_3
DDR4_4
Socket LGA1151
+12V Power
4
8
1
5
CPU FAN
1
Battery
JP11/12/13/14/15
PCI 2
PCI 5
6
2
6
2
6
5
1
6
5
2
1
JP1
JP2
2
JP4
JP3
1
S/PDIF
2
9
10
1
Front Audio
6
5
2
1
JP8
JP10
JP6
1
9
2
1
9
2
COM4
COM2
COM3
Buzzer
1
2
10
USB2_
9/14
1
2
7
8
1
13
12
24
ATX Power
1
2
11
Front
Panel
LAN LED
SPI Flash
BIOS
1
1
PCIe 1 (PCIe x16)
Digital I/O
JP7
1
System
Fan 1
1
System Fan 3
SATA 1
(R1)
SATA 0
(R0)
SATA 3
(R3)
SATA 2
(R2)
Mic-in
Line-out
Line-in (opt.)
VGA
COM 1
HDMI
DP++
LAN 2
USB3_1/2
USB2_1/2
LAN 1
USB3_3/4
USB2_3/4
USB7/8
Intel
Q470E/H420E
LPC
14
2
13
1
5
1
5
1
PCIe 2 (PCIe x4)
6
5
2
1
J12
1 1 1 1 1
DIO
Power
USB2_10
System Fan 2
1
9
2
6
5
2
1
6
5
2
1
6
5
2
1
1
JP5
(Clear CMOS)
USB2_5/6
USB3_5/6
USB2
11/12
1
1
1
1
SDJ2
1
6
CN37
PCI 1
PCI 3
PCI 4
1
9
2
1
9
2
COM5 COM6
SATA 5
(R5)
SATA 4
(R4)
1
10
2
1
10
11
1
PS2
1
JP27
1
JP28
1
JP26
1
JP23
JP24
1
20
10
11
The lithium ion battery addendum supplies power to the real-time clock and CMOS memory
as an auxiliary source of power when the main power is shut off. Insert a coin cell battery into
the holder and make sure the polarities are correctly oriented — the cap side (rimmed rounded
edge) is negative and should be facing the holder; the flat side with a + mark is positive and
should be facing away from the holder.
Safety Measures
• There exists explosion hazard if the battery is incorrectly installed.
• Replace only with the same or equivalent type recommended by the manufacturer.
• Dispose of used batteries according to local ordinances.
Battery
Battery
X
Internal I/O Connectors
