DeZurik PEF Installation And Operation Manual Download Page 7 | Manualshive

Page: 7 / 20

DeZurik PEF Installation And Operation Manual Download Page 7

DeZURIK

3---36" PEF 100% Port Eccentric Plug Valves

April 2015

Page 7

D10453

Installation

(Continued)

Liquids with Suspended Solids and Dirty Gases

If the pipeline carries suspended solids such as paper stock of 2 percent or higher consistency, mining
slurry, or raw sewage:

1. Before installation, remove foreign material such as weld spatter, oil, grease, and dirt from the

pipeline.

2. Prepare pipe ends and install valves in accordance with the pipe manufacture’s instructions for

the joint used.

Note:

See Figure 2 for proper valve orientation.

a.

In H

ORIZONTAL

pipelines, install the valve so that the plug is horizontal and rotates upward as

the valve opens.

b.

For V

ERTICAL

pipelines, install the valve with the end marked “S

EAT

” at top of valve.

Do not deflect the pipe-valve joint. Minimize bending stresses in the valve end
connection with pipe loading.

3. Ensure the valve and flanges are concentric to ensure proper flange sealing.

4.

Tighten the flange bolts or studs in a crisscross pattern.

«
...
5
6
7
8
9
...
»

Summary of Contents for PEF





















Reviews:

No comments