manualshive.com logo in svg

DeZurik PEF, Installation And Operation Manual, Page: 16 / 20

Share
Download
DeZurik PEF Installation And Operation Manual Download Page 16

DeZURIK

 

3---36" PEF 100% Port Eccentric Plug Valves

 

D10453 

Page 16 

April 2015 

 

Disassembly

 

(Continued)

 

11. Reaching through the packing chamber in the bonnet (A6), drive the bearing (A7) out of the 

bonnet using a hammer and pin punch. 

12. Remove the bearing (A2) from the body (A1). 

 

For 

3” - 20” valves

, the bearing (A2) can be chiseled out; or, it can be hydraulically forced out. 

 

See Figure 6. 

 

For 

24” - 36” valves

, the bearing (A2) can be driven out of the body (A1) using a hammer and 

 

pin punch. First remove the screws (A18) and journal cover (A17) from the body. Remove the 

 

old o-ring (16) from the journal cover. 

To hydraulically force the bearing (A2) out of 3” - 20” valve body: 

1.  Fill the interior diameter of the bearing (A2) with water. 

2.  Pound a shaft with the same outside diameter as the lower journal of the valve plug into the 

bearing (A2). 

 

 

Figure 6—Hydraulically Removing the Lower Bearing in the Valve Body 

 

Summary of Contents for PEF





















Reviews:

No comments