manualshive.com logo in svg

DeZurik PEF, Installation And Operation Manual, Page: 13 / 20

Share
Download
DeZurik PEF Installation And Operation Manual Download Page 13

  

DeZURIK

 

3---36" PEF 100% Port Eccentric Plug Valves

 

April 2015 

Page 13 

D10453 

 

Packing Replacement

 

(Continued) 

Note: 

 3 - 8” lever and nut operated valves have a friction cone (A21) and standard packing 

(A9). Before installing the gland (A11), set the friction cone on top of the packing. Do not 

lubricate the outside of the friction cone or the inside of the gland. See Figure 5. 

9.  Slide the gland (A11) down the plug shaft (A3) and over the studs (A12). If the valve has a 

friction cone (A21), bring the gland nuts (A13) under the gland up finger tight. 

 

Figure 5—Friction Cone Adjustment 

10. Adjust gland nuts (A13). 

3 - 8” L

EVER AND 

N

UT 

O

PERATED 

V

ALVES 

O

NLY

: 

Turn gland nuts (A13) onto the studs (A12) until they touch the gland (A11). 

Note: 

This is a preliminary adjustment, it will be necessary to adjust the gland nuts (A13) after the 

valve is pressurized. See "Packing Adjustment" section. 

11. Fasten the adaptor (when used) to the valve, lining up the scribe marks made during 

disassembly. 

12. Install the actuator as described in the Actuator Instructions. 

13. 

If the actuator is a powered actuator, reconnect power to the actuator.

 

Summary of Contents for PEF





















Reviews:

No comments