25
GB
LEROY MERLIN
– Rue Chanzy – Lezennes 59712 LILLE Cedex 9 – France
LEROY MERLIN
– Rue Chanzy – Lezennes 59712 LILLE Cedex 9 – France
6. Technical data
Electro motor
230 240 V ~ ,50 Hz
Power
S1 250W, S2 30 min 350W
Revolutions
1400 min
1
Saw band length
1400 mm
Saw band width
7 mm
Saw band width max.
12 mm
Cutting speed
900 m/min
Passage height
0 80 mm
Passage width
200 mm
Table size
300 x 300 mm
Slewing range of the
table
0° bis 45°
Max. size of the
workpiece
400 x 400 x 80 mm
Overall weight
19 kg
Subject to technical modifications!
* Operating mode S1, continous operation.
The work piece must have a minimum height of 3mm
and a minimum width of 10 mm.
Noise parameters
The total noise values determined in accordance
with EN 61029.
sound pressure level L
pA
77,4 dB(A)
uncertainty K
pA
3 dB
sound power level L
WA
90,4 dB(A)
uncertainty K
WA
3 dB
Wear hearing protection.
The effects of noise can cause a loss of hearing.
Total vibration values (vector sum three directions)
determined in accordance with EN 61029.
7. Remaining hazards
The machine has been built using modern technolo
gy in accordance with recognized safety rules. Some
remaining hazards, however, may still exist.
•
Risk of injury for fingers and hands by the rotating
saw band due to improper handling of the work
piece.
• Risk of injury through the hurling work piece due
to improper handling, such as working without the
push stick.
• Risk of damaging your health due to wood dust and
wood chips. Wear personal protective cloth such
as goggles. Use a fitting dust extractor.
• Risk of injury due to defective saw band. Regu
larely check saw band for such defects.
•
Risk of injury for fingers and hands while changing
saw band. Wear proper gloves.
• Risk of injury due to starting saw band while
switching on the machine.
• The use of incorrect or damaged mains cables can
lead to injuries caused by electricity.
•
Wear only closefitting clothes. Remove rings,
bracelets and other jewelry.
• For the safety of long hair, wear a cap or hair net.
Even when all safety measures are taken, some
remaining hazards which are not yet evident may
still be present.
• Remaining hazards can be minimized by follow
ing the instructions in
„
General safety instructions“
„Proper Use“ and in the entire operating manual.
8. Attachment and operation
Before starting the equipment
Make sure the machine stands securely, i.e. bolt it
to a workbench or solid base. There are two holes
for this purpose in the machine foot. • The saw table
must be mounted correctly.
• All covers and safety devices have to be properly
fitted before the machine is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws etc.
• Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine’s moving parts run smoothly.
• Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
Assembly tools
1 engineer’s wrench SW 10/13
1 hexagonal head spanner SW 3
1 hexagonal head spanner SW 4
Tabletop and the mounting angles are not mounted
for reasons of packaging technology.
8.1 Assembly of the table top (Fig.
1+2+3+4+4.1+4.2
)
1. Lay the table insert (14) in the recess in the work
table intended for this (7) (Fig. 3). (To replace, dis
assemble the work table in reverse order.)
2 Remove the wing nut (E), the clamping lever (F),
the two disks and the plate (H). (Fig. 4.1)
3 Position the working table (A) over the rear (B) to
the screws. Fasten the working table with the plate
(H), the two disks, the wing nut (E) and the clamp
ing lever (F) to the machine housing. Fig. 4.2).
4. Fit the bolt M6x35 with two washers and the nut to
the table. (Fig. 4.2)
8.2 Adjusting the table top (Fig. 5)
1 Set the table top to home position and tighten the
wing bolt (E) and the clamp lever (F) firmly.
2 Align the table top parallel to the sawing blade
and tighten the 3 screws. Observe that the sawing
blade is centred in the table inlay.
8.3 Adjusting the table top at the right angle to
the sawing blade(Fig. 4+5)
1 Fully set the belt guide (4) upwards and clamp it
tight. (8.11)
2 Release the clamping lever (F) and the wing bolt
(E) at the swivelling segment (G).
3 Align the table at the right angle (90°) to the sawing
blade (use back square).
4 Adjust the adjusting screw (I) and lock it with a
nut (J).
