Operating Instructions
1.
Ensure that power is turned on to the washer.
2.
Ensure that the ADVANCE/RUN/PROGRAM key lock is in the RUN position.
3.
Load the clothes loosely in the cylinder and latch the door securely. Be sure clothing does
not get caught between the door gasket and tub front when closing the door.
NOTE: To begin closing the door, the handle must be in the horizontal position. After moving the
door to the closed position, the handle must be turned down to the vertical position in order to latch
the door for machine operation.
4.
Select one of the thirty cycles, by using the SCROLL UP/SCROLL DOWN buttons to
change the number indicated in the two digit LED display. The selection is made when the
number indicated corresponds with the desired cycle.
5.
If you are manually adding wash compounds, add low sudsing powdered detergent in the
amount shown below into the detergent compartment on top of the machine or in front
soap compartment. Location is illustrated on the black cover on the top of the machine.
This compartment will be flushed during the WASH segment of the cycle. Rinse conditioners
may be added to their own compartment if desired. This compartment will be flushed
during the FINAL RINSE segment of the cycle.
6.
If you wish to manually add bleach during the cycle, add bleach in the round opening in
the top of the machine. Location is illustrated on the black cover on the top of the machine.
NOTE: Any additional washing compounds may be added at the appropriate time by pouring into the
round opening in the top.
7.
Push the green START button to start the cycle.
8.
The cycle time remaining is displayed throughout the cycle. The cycle number in operation
can be displayed by pushing and holding START, then push SCROLL UP. The cycle
number will be displayed as long as these two buttons are depressed.
The actual bath temperature can be displayed by simultaneously pushing the START and
SCROLL DOWN button.
Soak
- At any time during the cycle, the red STOP button can be depressed to stop the
washer timer from counting down. All washer cycle information is retained and the door
remains locked. The washer will soak the load for 15 minutes, then agitate for 30 seconds.
This will repeat until the cycle is started again. This feature allows for an extended soak if required. The
washer cycle will continue when the START button is depressed.
NOTE: The selected cycle can be cleared at any time by depressing and holding the STOP button for
a minimum of three seconds.
End of Cycle
At the end of the cycle the machine stops, the END CYCLE LED lights, the alarm sounds, and the loading
door unlocks allowing unloading of the machine.
Safety Door Lock
This machine is equipped with a Safety Door Lock which prevents opening the door if power is interrupted,
until it is safe to do so.
If power failure occurs, it will be necessary to wait 2 to 3 minutes before the door can be opened.
Motor Drive indicators
There is a five digit, seven segment, display on the drive which can be viewed by removing the access cover
at the top rear of the washer. There are also small L.E.D.s on the left and bottom edge of the display that
can be viewed and used for troubleshooting. The five seven segment digits will change value depending on
where the washer is during the wash cycle.
Computer Contol Indicators
Computer control OPL machine has 30 different selectable cycles; 29 of the 30 cycles are preset with the
most common industry applications. See the Preset Cycle Information sheets for complete cycle information.
If these cycle settings do not meet the required application, each cycle is re-programmable by the user,
simply and reliably.
Each cycle has up to 9 baths which are Flush, Pre-wash, Wash, Rinse 1, 2, 3, 4, 5 and Final Rinse/Extract.
There are five user selectable settings within each bath to allow cycle tailoring to meet exact applications.
The settings and the limits of each are shown in the table below. The Scroll Up/Scroll Down buttons are
used to change the settings.
Bath Setting Limits
Cycle Time - 0 to 30 minutes (1 minute increments)
The Cycle time (tumble) settings are 0 minutes to 30 minutes in 1 minute increments for
each bath. If the setting is 0, then that bath is skipped over. For the Final Rinse /Extract
bath, the minimum time must be 1 minute.
Water Temperature - Hot, Warm, Cold, Empty (20-90C if heated model)
The water temperature setting is displayed as HH = hot, CH = warm, CC = cold, EE = No
water bath, 20-90C in 5 degrees increments. When the No Water or EE bath is selected,
the water level can be set to either high or low and NO Injection will be made even if the
injection source is programmed. Maximum temperature for final rinse is 60 C.
Water Level - High or Low
The water level setting is displayed as HI for high level and LO for low level.
Injection Source 0 to 6
The injection source settings are 0 through 6 with 0 being no injection and settings 1 through
6 relating to an injection source. See Recommended Injection Table.
Spin Time - 0 to 10 minutes (1 minute increments)
The spin time settings are 0 minutes to 10 minutes in 1 minute increments. If the setting is
0, there is no spin for the
bath. Final Rinse/Extract minimum setting is 1 minute.
Part # 8533-096-001 11/16
Part # 8533-096-001 11/16
24
25
