Outer Tub
Removal
Step 1:
The outer tub can easily be removed when the tub back, bearing, and cylinder assembly have been
removed as outlined.
Step 2:
At that point only attachments to the chassis are the two front strap mounting bolts.
Reassembly
Step 1:
Install outer tub in front strap leaving bolts loose.
Step 2:
Install tub back assembly in washer (see Reassembly of Tub Back, Bearing, and Cylinder (basket)
Assembly).
Step 3:
With tub tback assembly bolted to washer frame and to the back of the outer tub, tighten front strap
bolts.
Tub Back, Bearing and Cylinder Assembly
Reassembly
Step 1: Use the hub of the drive
pulley, a stack of 5/8” flat
washers and a 3” long 5/8”
bolt to pull the cylinder
shaft through the bearings.
After the 3” bolt a 2” long
bolt will be required to fin
ish pulling the cylinder shaft
through.
Step 2: Remove the 1/2” bolt and
nut from the top of the
outer tub clamping band.
Step 3: Install Dexter Tool part#
8545-056- 001 on the
back of the outer tub to
adjust tub front to cylinder
clear ance. Thread 5/8”
bolt through tool and into
cylinder shaft. Push the
outer tub forward 1/4” to
1/2” with tool 8545-056-001
by tightening the 5/8” bolt.
This will ease the installa
tion of the outer tub front.
Step 4: Clean the silicone rubber off
the tub front and the outer
tub.
Step 5: Install new bead of silicone
rubber on tub front.
Step 6: Install tub front.
Step 7: Install drive pulley and belts.
Step 8: Install back panel.
Step 9: Install door lock.
Step 10: Install door, masking ring,
front panel, lower service
panel, and top panel.
Removal
Step 1:
Remove the top panel as described previously.
Step 2:
Remove lower service panel as described previ- ously.
Step 3:
Remove front panel as described previously.
Step 4:
Remove masking ring as described previously.
Step 5:
Remove door lock assembly. (Leave wires & pull rod in
place)
Step 6:
Remove clothes door.
Step 7:
Remove tub front clamp ring.
Step 8:
Remove tub front. Use a flat screw driver to pry the tub
front loose.
Step 9:
Remove the rear access panel.
Step 10:
Remove the drive belts.
Step 11:
Remove drive pulley.
Remove 3 retaining screws.
Insert 3 2” screws into the threaded removal
holes.
Alternately tighten these screws evenly to pull
the pulley off.
Step 12:
Remove pulley hub. Drive a flat screw driver into
the slot in the hub and pull it from the shaft.
Step 13:
Install cylinder puller.
(Snap On part #CJ-84-C) Be sure to thread a bolt into
the end of the cylinder shaft to protect the threads.
Step 14:
Push the basket out.
Installing Tub Front
Step 1:
Align hole in top of tub front with notch in top of outer tub.
Step 2:
Use 4-6 #11R vise grip clamps to hold tub front to outer tub. A rubber mallet may be needed to
properly seat the tub front into the outer tub.
Step 3:
Install tub front gasket around outer edge of tub front and outer tub flange. The opening should be
centered at the top.
Step 4:
Remove vise grips. The tub front gasket will hold the tub front in place.
Step 5:
Install tub front clamp ring and tighten. Tap around the clamp ring with a rubber mallet to seat the
ring and gasket while tightening the clamp ring bolt.
Step 6:
Adjust clearance between the outer tub front and the front lip of the cylinder to 5/16”
Step 7:
Tighten the outer tub clamping band.
Step 8:
If necessary, adjust the outer tub with the 2 bolts that fasten the tub clamping band to the frame.
Step 9:
Remove Dexter tool part 8545-056-001 from the back of the other tub.
Step 10:
Install drive pulley.
42
43
Part # 8533-031-001 6/22
Part # 8533-031-001 6/22
Machine
Mounting
Installation
& Operation
Trouble-
shooting
Machine
Service
Electrical
Wiring
Parts
Data
Coin
Handling
Maintenance
