DeWalt XR Li-Ion Flexvolt DCG200, Original Instructions Manual

Page: 14 / 56

12
English
WARNING:
• Apply only a gentle pressure to the tool. Do not exert
side pressure on the diamond blade.
• Always wear appropriate safety equipment like eye
and hearing protection and regular working gloves
while operating this tool.
• The gear case becomes very hot during use.
• Always install the guard and appropriate diamond
blades. Do not use excessively worn diamond blades.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
3. Ensure the flange is seated correctly by rotating it until it
slots into place.
4. Place a diamond blade 21 against the backing flange,
centring the diamond blade on the raised centre (pilot) of
the backing flange.
5. Ensure the direction arrows on the diamond blade match
those that are molded into the inside of the guard.
6. To create the desired groove width between the two
diamond blades, add spacers
17
as needed with the raised
centre (pilot) facing upward.
7. Place the second diamond blade on the spacer.
8. Install any remaining spacers.
9. While depressing the spindle lock button
3 and with the
hex depressions facing away from the diamond blade,
thread the threaded locking flange
8 on the spindle so that
the lugs engage the two slots in the spindle.
10. While depressing the spindle lock button, tighten the
threaded locking flange with the hex wrench.
11. Securely latch the guard locking lever.
12. To remove the diamond blades, depress the spindle lock
button and loosen the threaded locking flange with the
hex wrench.
Prior to Operation
• Be sure the inner and outer flange are mounted correctly.
• Make sure the diamond blades rotate in the direction of the
arrows on the accessory and the tool.
• Do not use a damaged diamond blade. Before each use
inspect the diamond blades for chips and cracks or excess
wear. If the power tool or diamond blade is dropped,
inspect for damage or install an undamaged diamond blade.
After inspecting and installing a diamond blade, position
yourself and bystanders away from the plane of the rotating
diamond blade and run the power tool at maximum
no-load speed for one minute.
• Be sure the inner and outer flange are
mounted correctly.
• Make sure the diamond blade rotates in the direction
of the arrows on the accessory and the tool.
• Avoid overloading. Should the tool become hot, let it
run a few minutes under no load condition to cool the
diamond blades. Do not touch diamond blades before
they have cooled. The diamond blades become very
hot during use.
• Do not use the power tool with a cut-off stand.
• Never use blotters together with diamond blades.
• Be aware, the diamond blades continue to rotate after
the tools is switched off.
Proper Hand Position (Fig. E)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle 5 ,
with the other hand on the auxiliary handle
6
Wireless Tool Control (Fig. A)
CAUTION: Read all saftey warnings, instruction and
specifications of the appliance which is paired with the
wall chaser.
Your wall chaser is equipped with a Wireless Tool Control
transmitter which allows your wall chaser to be wirelessly
paired with another Wireless Tool Control device, such as a
dust extractor.
To pair your wall chaser using Wireless Tool Control, press and
hold the trigger switch
1
on the wall chaser and the Wireless
Tool Control pairing button on the seperate device. An LED on
the seperate device will let you know when your wall chaser has
been successfully paired.
Trigger Switch and Lock-off Lever (Fig. F)
1. To turn the tool on, push the lock-off lever 2 toward the
back of the tool, then depress the trigger switch
1
. The tool
will run while the switch is depressed.
2. Turn the tool off by releasing the trigger switch.
WARNING: Hold the auxiliary handle and body of the
tool firmly to maintain control of the tool at start up and
during use and until the diamond blades stop rotating.
Make sure the diamond blades have come to a complete
stop be fore laying the tool down.
WARNING: Allow the tool to reach full speed before
touching tool to the work surface. Remove the tool from
the work surface before turning the tool off.
Spindle Lock (Fig. G)
The spindle lock button 3 is provided to prevent the spindle
from rotating when installing or removing diamond blades.
Operate the spindle lock only when the tool is turned off,