34
EngLIsh
SDS plus® and SDS max® are registered trade marks of
Robert Bosch GmbH
Protecting the Environment
w
Separate collection. Products and batteries marked
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that
can be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com
.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
• Run the battery pack down completely, then remove it from
the tool.
• Li‑Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
Optional Accessories
WARNING:
Since accessories, other than those offered by
D
e
WALT
D
e
WALT
, have not been tested with this product,
use of such accessories with this tool could be hazardous.
To reduce the risk of injury, only
D
e
WALT
D
e
WALT
recommended accessories should be used with
this product.
Consult your dealer for further information on the
appropriate accessories.
D
Cleaning
WARNING:
Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING:
Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
C
Lubrication
Your power tool requires no additional lubrication.
installing attachments or accessories.
An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Wireless Tool Control (Fig. A)
CAUTION:
Read all saftey warnings, instruction and
specifications of the appliance which is paired with
the hammer.
Your hammer is equipped with a Wireless Tool Control
transmitter which allows your hammer to be wirelessly
paired with another Wireless Tool Control device, such as a
dust extractor.
To pair your hammer using Wireless Tool Control, press and
hold the trigger switch
1
on the hammer and the Wireless Tool
Control pairing button on the seperate device. An LED on the
seperate device will let you know when your hammer has been
successfully paired.
3. Set the mode selector switch
4
to the “hammering
Only” position.
4. Twist the chisel until it locks in position.
Performing an Application (Fig. A)
WARNING:
TO REDUCE THE RISK OF PERSONAL
INJURY, ALWAYS
ensure workpiece is anchored or
clamped firmly. If drilling thin material, use a wood
“backup” block to prevent damage to the material.
Switching On and Off (Fig. A)
To turn the tool on, depress the trigger switch
1
.
To stop the tool, release the trigger switch.
Chipping and Chiselling (Fig. A)
1. Insert the appropriate chisel and rotate it by hand to
lock it into one of chisel positions. Refer to
Indexing the
Chisel Position
.
2. Set the mode selector switch
4
to the 'hammering
only' position.
3. Set the electronic speed and impact control dial
10
.
4. Fit and adjust the side handle
2
.
5. Turn the tool on and start working.
6. Always turn the tool off when work is finished and
before unplugging.
Recommendations for Tool Operation
WARNING:
• Do not use this tool to mix or pump easily combustible
or explosive fluids (benzine, alcohol, etc.).
• Do not mix or stir inflammable liquids
labelled accordingly.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
WARNING:
To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
