background image

English

4

DANGER: This machine was built to be operated according to the safe 

operation practices in this manual. As with any type of power equipment, 

carelessness or error on the part of the operator can result in serious injury. 

This machine is capable of amputating hands and feet and throwing 

objects. Failure to observe the following safety instructions could result in 

serious injury or death.
WARNING: CALIFORNIA PROPOSITION 65 - Engine exhaust, some of its 

constituents, and certain vehicle components contain or emit chemicals 

known to the State of California to cause cancer and birth defects or other 

reproductive harm. 
Battery posts, terminals, and related accessories contain lead and lead 

compounds, chemicals known to the State of California to cause cancer and 

reproductive harm. Wash hands after handling. 
WARNING:   This symbol points out important safety instructions which, 

if not followed, could endanger the personal safety and/or property 

of yourself and others. Read and follow all instructions in this manual 

before attempting to operate this machine. Failure to comply with these 

instructions may result in personal injury. When you see this symbol. HEED 

ITS WARNING!

Training

1.  Only allow operators who are responsible, trained, familiar with the instructions, and 

physically capable to operate the mower.

2.  Be familiar with the areas in which the mower is to be used. Walk all areas to be 

mowed, evaluate slopes and other terrain and look for obstacles to be avoided to 
ensure safe operation before mowing.

3.  See the Practice Operation section of this manual for further instructions.

General Operation

1.  Be familiar with all controls and their proper operation. Know how to stop the mower 

and disengage the controls quickly.

2.  Do not allow anyone to operate or maintain this mower who has not read the 

manual. Never permit children under the age of 16 to operate this mower. 

3.  Do not remove any shields, guards, labels or safety devices. If a shield, guard, label or 

safety device is damaged or does not function, repair or replace it before operating 
the mower.

4.  To help avoid blade contact or a thrown object injury, keep bystanders, helpers, 

children and pets at least 75 feet (22.9 meters) from the mower while it is in 
operation. Stop mower if anyone enters the area.

5.  Thoroughly inspect the area where the equipment is to be used. Remove all stones, 

sticks, wire, bones, toys, and other foreign objects that could be picked up and thrown 
by the blade(s). Thrown objects can cause serious personal injury.

6.  Evaluate the terrain to determine what accessories and attachments are needed to 

properly and safely perform the job.  Only use accessories and attachments approved 
by the mower manufacturer.

7.  Plan mowing pattern to avoid discharge of material toward roads, sidewalks, 

bystanders and the like. Also, avoid discharging material against a wall or obstruction 
which may cause discharged material to ricochet back toward the operator.

8.  Always wear appropriate clothing and personal protective equipment (e.g. safety 

glasses, long pants, gloves, hearing protection , safety shoes, hard hat) when 
operating or maintaining this mower. Long hair, loose fitting clothing or jewelry may 
get entangled in moving parts. Follow all federal, state and local guidelines regarding 
the use of personal protective equipment.

9.  For extended use of this product, hearing protection is recommended.

10.  Be aware of the mower and attachment discharge direction and do not point it 

at anyone. Do not operate the mower without the discharge cover or entire grass 
catcher in its proper place.

11.  Do not put hands or feet near rotating parts or under the cutting deck. Contact with 

the blade(s) can amputate hands and feet.

12.  A missing or damaged discharge cover can cause blade contact or thrown 

object injuries.

13.  Stop the blade(s) when crossing gravel drives, walks, or roads and while not 

cutting grass.

14.  Watch for traffic when operating near or crossing roadways. This mower is not 

intended for use on any public roadway.

15.  Do not operate the mower while under the influence of alcohol or drugs.

16.  Mow only in daylight or good artificial light.

17.  Never carry passengers.
18.  Back up slowly. Always look down and behind before and while backing to avoid a 

back-over accident.  

19.  Slow down before turning. Operate the mower smoothly. Avoid erratic operation and 

excessive speed. Be aware of the direction of travel to avoid accidents.

20.  Disengage blade(s), set parking brake, stop engine and wait until the blade(s) come 

to a complete stop before removing grass catcher, emptying grass, unclogging chute, 
removing any grass or debris, or making any adjustments. 

21.  Never leave a running mower unattended. Always stop on level ground, turn off 

blade(s), place drive speed control levers in neutral, set parking brake, stop engine 
and remove key before leaving the operator position.

22.  Use extra care when loading or unloading the mower on a trailer. The mower should 

not be driven on unstable, unsecured or inadequate ramps because the mower could 
tip over causing serious personal injury.

23.  Check overhead clearances carefully before driving under low hanging tree branches, 

wires, door openings etc., where the operator may be struck which could result in 
serious injury.

24.  Muffler and engine become hot and can cause a burn. Do not touch.
25.  Disengage the blades, set the parking brake to the ‘on’ position and make sure the 

speed control levers are in the  neutral position before attempting to start the engine. 
Only start the engine from the operator’s position.

26.  Do not attempt to mow unusually tall, dry grass (e.g., pasture) or piles of dry leaves. 

Dry grass or leaves may contact the engine exhaust and/or build up on the mower 
deck presenting a potential fire hazard.

27.  Do not stop or park the mower over dry leaves, grass, debris or other 

combustible material.

28.  Never attempt to operate the mower without the mowing deck attached; the mower 

could tip over.

29.  Keep the mower and especially the engine exhaust system and hydraulic 

components clean and free of grease, grass and leaves to reduce the potential for 
overheating and fire.

30.  Allow the mower to cool at least 5 minutes before storing.
31.  Use only accessories and attachments approved for this mower by the mower 

manufacturer. Read, understand and follow all instructions provided with the 
approved accessory or attachment. 

32.  Data indicates that operators, age 65 years and above, are involved in a large 

percentage of riding mower-related injuries. Operators should evaluate their ability 
to operate this mower safely enough to protect themselves and others from serious 
injury. 

33.  Do not operate or start mower if there is fuel or oil leaks; repair immediately.
34.  When looking for oil leaks, never run hands over hydraulic hoses, lines or fittings. 

Never tighten or adjust hydraulic hoses, lines or fittings while the system is under 
pressure. If high-pressure oil penetrates the skin seek immediate medical attention or 
gangrene and permanent damage may result. Do not check for hydraulic leaks with 
hands, use paper or cardboard instead. Wear gloves and safety glasses when checking 
for leaks.

35.  Do not operate mowers that have been damaged or have not been properly 

maintained. If the mower has been damaged, then have it repaired.

36.  When operating this mower in the forward direction, do not allow the speed control 

levers to return to the neutral position on their own. Always operate them smoothly 
and avoid any sudden movements of the levers when starting or stopping.

37.  If situations occur which are not covered in this manual use care and good 

judgement. Contact the customer service representative for assistance.

Slope Operation

Slopes are a major factor related to loss of control and tip-over accidents that can result in 
severe injury or death. All slopes require extra caution. If you cannot back up the slope or 
if you feel uneasy on it, do not mow it or drive on the slope. 
For your safety, use the slope gauge included as part of this manual to measure slopes 
before operating this mower on a sloped or hilly area. If the slope is greater than 15 
degrees as shown on the slope gauge, do not operate this mower on that area or serious 
injury could result.

Do:

1.  Mow across slopes, not up and down. Exercise extreme caution when changing 

direction on slopes.

2.  Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain could 

overturn the mower. Tall grass can hide obstacles.

3.  Use slow speed. Choose a low enough speed so that the mower will not have to 

stop while on the slope. Avoid starting or stopping on a slope. If the tires are unable 
to maintain traction, disengage the blades and proceed slowly and carefully straight 
down the slope. 

SAFE OPERATION PRACTICES

Summary of Contents for X536





























































Reviews: