English
6
Assembling Spray Wand (Fig. E)
1. To connect the spray handle
4
to the handle grip
5
,
insert the threaded end of the spray handle onto the
threaded end of the handle grip. Rotate the spray handle
4
clockwise until fully tightened.
2. To connect the spray wand
2
to the spray handle
4
, insert
the threaded end of the spray wand into the threaded
collar
29
of the spray handle. Rotate the threaded
collar
29
clockwise until fully tightened.
Accessory Storage Compartment (Fig. D)
This pressure washer has a built in accessory storage
compartment
34
to carry the spray wand, spray handle,
handle grip and turbo nozzle.
1. To unlock the storage door
10
, rotate the door
latch
11
counterclockwise and flip the door down
to access the spray wand
2
, spray handle
4
, handle
grip
5
, and turbo nozzle
22
.
2. To lock the storage door
10
, lift the storage door up to the
closed position. Rotate the door latch
11
clockwise to lock
the storage door into position.
Telescoping Handle (Fig. C)
This pressure washer has a convenient, built in telescoping
handle and transport wheels.
1. To unlock the telescoping handle
13
, press the handle
release button
14
and slide the handle upwards. You will
hear an auidible click when it snaps into position.
2. To store the telescoping handle
13
, press the handle
release button
14
and slide the telescoping handle
down and into the pressure washer body. You will hear an
auidible click when it snaps into position.
3. To move the pressure washer
8
, tilt the unit so the
transport wheels
21
are touching the ground and pull the
unit by the telescoping handle.
Cage Carrying Handles (Fig. B)
This pressure washer has a protective cage that protects the
pressure washer from daily jobsite abuse but also provides
mulitiple carry handle
12
options. Carry the pressure washer
using whichever part of the cage that is convenient for
your application.
Specifications
Maximum Pounds per Square Inch*
2100
Rated Gallons per Minute*
1.2
Electrical Requirements
120V
AC
~60Hz, 13A
Electrical Cord
35 ft. (10.6 m)
High Pressure Hose
25 ft. (7.6 m)
Minimum Amp Source
15A
Pressure of Inlet Water
20‑100 PSI
Inlet Water
Cold Tap
*Water flow and maximum pressure ratings determined in accordance with
CETA CPC‑100.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. These tools are factory tested; if
this tool does not operate, check power supply.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz .......................hertz
min .....................minutes
or DC ......direct current
...................... Class I Construction
(grounded)
…/min ..............per minute
BPM ....................beats per minute
IPM .....................impacts per minute
OPM .................... oscillations per
minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM ....................strokes per minute
A .........................amperes
W ........................watts
Wh ......................watt hours
Ah .......................amp hours
or AC ...........alternating current
or AC/DC .... alternating or direct
current
...................... Class II Construction
(double insulated)
no .......................no load speed
n .........................rated speed
PSI....................... pounds per square
inch
......................earthing terminal
.....................safety alert symbol
..................... visible radiation
do not stare into
the light
..................... wear respiratory
protection
..................... wear eye protection
..................... wear hearing
protection
..................... read all
documentation
minimum wire size. The following table shows the correct
size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gauge. The
lower the gauge number, the heavier the cord.
Minimum gauge for Cord sets
Volts
Total length of Cord in Feet
(meters)
120 V
25 (7.6)
50 (15.2) 100 (30.5) 150 (45.7)
240 V
50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
Ampere Rating
American Wire gauge
More
Than
not
More
Than
0
6
18
16
16
14
6
10
18
16
14
12
10
12
16
16
14
12
12
16
14
12
Not Recommended
Summary of Contents for DWPW2100
Page 5: ...3 Fig H Fig I Fig J Fig K Fig L Fig N Fig M 26 3 4 5 27 27 28 8 28 8 9 34 10 2 ...
Page 30: ......
Page 31: ......
