6
English
Description (Fig. A)
WARNING:
Never modify the power tool or any part of it.
Damage or personal injury could result.
1
Spindle
2
Spindle lock button
3
Collet nut
4
Small spanner (13 mm)
5
Large spanner (17 mm)
6
Collet 6 mm
7
Paddle switch
8
Lock-off button
9
Variable Speed Dial
10
LED indicator
11
LED worklight
Intended Use
Your die grinder has been designed for professional grinding
applications. The tool can be used with the complete range of
commerical grinding accessories with a maximum diameter of
50 mm and approved minimum speed of 25000/min.
DO nOT
use under wet conditions or in the presence of
flammable liquids or gases.
This die grinder is a professional power tool.
DO nOT
let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Features
No-volt Protection
The ON/OFFswitch has a no-volt release function. In the event of
a power outage or other unexpected shut down, the switch will
need to be cycled (turned on and off) to restart tool.
E-Clutch
This unit is equipped with an E-Clutch (Electronic Clutch), which
in the event of a stall or wheel pinch, the unit will be shut off to
reduce the reaction torque to the user. The switch needs to be
cycled (turned on and off) to restart tool.
Brake
When the trigger switch is released the motor immediately
turns off and electronically brakes, stopping the accessory
quickly to prevent accidental contact and improve productivity.
Constant Clutch
When overloaded or stalled the motor torque is reduced to
allow the user to maintain control of the tool. If load is reduced
the torque and RPM will increase. If the tool is stalled for an
extended amount of time it will shut-off and require the switch
to cycle to restart. This feature mimics a mechanical clutch
without the associated component wear.
Variable Speed Dial (Fig. A)
WARNING:
Regardless of the speed setting, the rated
speed of the accessory must be at least equal to the
maximum speed marked on the power tool.
The variable speed dial offers added tool control and enables
the tool to be used at optimum conditions to suit the accessory
and material.
• Turn the dial
9
to the desired level. Turn the dial upward for
higher speed and downwards for lower speed.
LED Indicator (Fig. A)
The LED indicator
10
will remain lit green during normal
activity, or blink in a pattern of red light to alert you a tool
protection feature has been activated. Refer to the
LED Guide
at
the back of this manual for explanations of blink patterns.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Mounting an Accessory (Fig. A)
WARNING:
Accessories must be rated at least equal to the
maximum speed marked on the tool. Accessories running
faster than their rated speed can break and fly apart.
WARNING:
Accessories must be within the capacity rating
marked on the tool. Incorrectly sized accessories cannot be
adequately controlled.
WARNING:
Do not use accessories with a mandrel length
exceeding 40 mm. Ensure that the exposed mandrel
length is no more than 10 mm after inserting accessory
into collet.
WARNING: Projectile hazard. Only use accessories
with shanks that match the installed collet.
Smaller
shanks will not be secure and could become loose
during operation.
CAUTION:
Never tighten the collet without first installing
an accessory in it. Tightening an empty collet, even by
hand, can damage the collet.
1. Hold the spindle
1
using the spindle lock button
2
.
2. Loosen the collet nut
3
by turning it counterclockwise.
3. Insert the shank of the accessory into the collet
6
.
4. Securely tighten the collet using the larger
spanner
5
provided.
To remove the accessory, proceed in reverse order.
OPERATION
Instructions for Use
WARNING:
Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
