English
FIG. 6
FIG. 7
STEP 11. Parallel the front rail to the saw table (Fig. 6).
Using your fence face or a straightedge to extend the
table surface over the rail, make sure the distance from
the saw table top to the rail top is the same at both the
left and right side of the table. If the rail is not aligned
correctly, loosen the mounting screws slightly and tap
on the rail with a soft hammer or a regular hammer and
a block of wood until the distances are the same.
Tighten the hardware securely.
STEP 12. Attach left and right support tables (Fig. 7).
You will need: 6 - 10 x 25mm hex head bolts
6 - 10mm flat washers
6 - 10mm lock washers
Without the support table in place, install the 3 bolts per
side with washers as shown keeping 1/4" gap. Rest a
support table on the bolts, fitting into the notches. Using
the extruded fence face as a straightedge, flush the
support table to the saw table edge and snug the front
bolt. Repeat this process for the rear bolt and the cen-
ter bolt. Tighten hardware. Repeat on the other side.
STEP 13. Attach front rail bracket to support tables (Fig
4).
You will need: 2 - 10 x 25mm flat head screws
2 - 10mm flat washers
2 - 10mm lock washers
2 - 10mm nuts
Align front bracket with support table and tighten brack-
et nut to the rail. Attach the support tables to the outer
front rail support brackets, keeping the washers and
nut on the inside of the table. Using the fence face as
a straight edge, make sure the front outer corner of the
support table is level with the inner edge and main
table surface.
Tighten hardware, including the 8mm rail support
bracket nut. Repeat this procedure for the other sup-
port table.
STEP 14. Attach hanger brackets to saw table (Fig. 8).
You will need: 2 - 10 x 35mm hex head bolts
2 - 10mm flat washers
2 - 10mm lock washers
2 - 10mm nuts
Secure a bolt through the square hole in each bracket
with a flat washer, lock washer, and nut, keeping the
washers and nuts to the inside of the table. When tight-
ening nuts, keep the brackets positioned square to the
table. (With another accessory in place, insure the
hanger brackets are placed between the rear rail and
the saw table.)
STEP 15. Attach two rear support brackets (Fig. 9).
(With other accessories in place, rear support brack-
et(s) are not needed. The rear rail will attach directly to
the accessory).
You will need: 2 - 10 x 25mm hex head bolts
2 - 10mm flat washers
2 - 10mm lock washers
2 - 10mm nuts
Secure a bolt through the round hole in each bracket
with a flat washer, lock washer, and a nut, keeping the
washers and nut to the inside. Make sure hardware is
placed to the top of the slot in the rear of the support
table(s) and tighten. When tightening, keep the brack-
ets positioned square to the table.
FIG. 8
FIG. 9
STEP 8. Unpack rail carton (contains front & rear rail) and
Outfeed Table carton.
STEP 9. Assemble front rail and brackets (Fig. 4).
You will need: 4 - 8mm carriage bolts (3 if adding a
Slide Table)
4 - 8mm lock washers
4 - 8mm nuts
Assemble carriage bolts, washers and nuts to front rail
brackets (just a few threads). Put the head of the car-
riage bolts into the keyhole slots in the front rail and
slide to engage the square part of the bolt. Run nut
until it is finger tight Repeat for other three brackets (If
you are also adding a Slide Table accessory, the left
most front rail bracket is not needed). When attaching
brackets to the rail, the rail must be positioned so that
the rip scale is right side-up. Also all 4 brackets should
face the same direction
STEP 10. Attach front rail with brackets to the table
top (Fig. 5)
You will need: 2 - 10 x 30mm flat head screws
2 - 10mm flat washers
2 - 10mm lock washers
2 - 10mm nuts
Secure each screw through the upper hole in the cen-
ter brackets keeping the flat washer, lock washer and
nut to the inside of the table. Tighten snug but not very
tight. Tighten center rail bracket 8mm nuts, leaving the
outer ones finger tight.
FIG. 4
FIG. 5